Is it accurate to say that if you don't specify a logging source-interface that all logging info will go to the specified logging server.Thanks
Is it accurate to say that if you don't specify a logging source-interface that all logging info will go to the specified logging server.Thanks
I have a problem. I have a Router Cisco 2611 Serie Number JMX0522K441 with System Bootrap Version 11,3(2)XA4 with 32MB from DRAM and 8MB Memory Flash. My Router in the Boot Show me a messages:loadprog Bad file Magic Number 0X0Boot Cannot load flashD...
Hi ,We would like to see the serial number of C2600XM via Ciscoworks .Through Ciscoworks also we are only getting processor board id hence we want to know whether after configuring snmp-server chassis-id command in the router config Ciscoworks will s...
Hi, I need to mover the module WS-X6408A-GBIC from Catalyst 6500 to Catalyst 4500R... Is it possible ?Is possible move to another chassis ?Thanks
I have a rather basic question regarding the Wan Ethernet 10/100 interface of Cisco 1712.According to documentation, the internal 4-port switch fully supports Inter-VLAN routing, but what about the Wan Ethernet Interface? Being an IOS box, there ...
Is it possible to place extended IP access lists on 2950 switche's fast ethernet and gigabitports?Is this done in hardware (i.e wire speed) or software, and does it degrade the switch's performance?Can these ACLs be plased on trunk links?Thanx
I received a phone call from a customer, they tried the following images and 3620s don't see the WIC-1ADSL. She had opened a TAC case, the image they sent her (12.3(9a)) didn't show the WIC-1ADSL either. She tried multiple ADSL cards in multiple rou...
Somebody has asked me question that if we only want to use router for controlling broadcast traffice on WAN links and just control the routes between different networks, then we can use windows based or linux based OS as a router with OSPF or IGRP en...
According to CCO I need 128MB DRAM and 32MB Flash minimum for 12.3T IPSEC/IDS images.I had problems locating a 32MB Flash via google, GoldenRam, Cisco Memory dealers, etc. Any ideas on why I can't find a 32MB flash for a 3640? Larges I could find w...
hi, Is there an issue why catalyst 3750 is not displayed in the user tracking table, even host connected to the device? Im using IDU8.0 for the campus manager3.3, IOS version of WS-3750-48TS runs on 12.2(20)SE2 with k9 feature. All other swithes on t...
I'm running 6500/Sup720 with native IOS and want to bridge two dot1q subinterfaces (on different physical interfaces) and route IP traffic via BVI interface. I can configure bridging configuration and "bride irb" but can not create BVI interface. Reg...
DOes the fiber optic interfaces present in the WS-X4013+TS supervisor module support for uplink backbone connectivity ?The spec sheet says that these ports can be used for server connectivity and doesn't mension anything about uplink connections.
I have three Cisco routers and a Netopia Cable modem router. The Commerce network is setup as 192.168.4.0 on Serial0 and 192.168.5.0 on Ethernet0. The Plant49 router is setup on network 192.168.4.1 on Serial0 and 192.168.2.1 on Serial1 and 192.168....
Are these values based on layer-2 or layer-3 bit rate?Best Regards.
With the following BGP lab, In the lab, I want to verify two things.I know RTA learn two network 192.168.169.0/24 and 192.168.167.0/24 via AS200 and AS300. If the no. of AS path is the same, then how RTA determine 192.168.169.0/24 use 172.0.0.2 as ne...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 03-24-2025 06:42 AM | ||
| 02-26-2025 06:41 PM | ||
| 01-22-2025 07:00 AM | ||
| 01-22-2025 05:28 AM | ||
| 12-30-2024 06:12 PM |