how can i bring up an interface that says "line protocol and interface administratively down". what could be the probably course of it going down?
how can i bring up an interface that says "line protocol and interface administratively down". what could be the probably course of it going down?
How can I do a destination address translation on a Pix in the more secure to less secure direction?
Hi all,I have question regarding the USer tracking , last week i added a new 6509 switch device to RME , when i had problems with a particular PC connected to one of the port i tried looking it up in the user Tracking ,wont find the PC connected to t...
A Cisco guide says: "You can specify additional servers so that should one go offline, another will be available to receive messages.". Does it mean that both receive the messages or the second will receive only when first fails?
folksi want to set up an authentication server for logging onto my routers/switches but i'm not sure which of the above to go foranyone any suggestions/preferences or installation guidesthanks to anyone taking the time to reply
I need a cisco router with 4 ethernet 10/100 , 4 serial ports (64 /2MB) & 1 NM-4B-S/T . Which Cisco router will i go for in 2600 series I basically read about new Cisco 2800 router which offers a 4 port 10/100 WIC card & 4 WICs & NM slot will this ro...
I'd like to know if there is no probe installed on the network what can RTM monitor. Can it find out the utilization of a vlan? Or the CPU utilization of switches?
Is there an equivalent command of "SH port" (catos) in native IOS? The sh port in catos was very useful in getting a status of all ports quickly.Thx!
Hi everybody,i try to generate a SNMP trap on a Cisco 26xx if a eigrp neighbour changes occures. Unfortunatelly without success so far. Does somebody knows the configuration for that problem. - Thanks a lot for your feedback.regardsstephan
I've got an old 1720 w/T1 DSU/CSU module in it. I needed an ethernet WIC so I got the 1ENET which is suppose to be supported. In order to support it I upgraded to IOS 12.3(6). The router has more than the 32/8 requirements for 12.3(6).My problem i...
Folks, I have an X.25 to TCP translation configured... translate x25 2776 tcp 192.168.128.114 port 2776 stream quiet swap.. if I try to delete this with active VCs, I get.. cisco2(config)#no translate x25 2776%Translate: Can't delete/add entry - Co...
I have a 3750 L3 and use a linux bride to authenticate wireless users. All Wlan host are on VLAN 41 and the linux bridge connect vlan 41 to vlan 40. vlan 40 is a routed interface on the 3750. Vlan 41 are only a L2 local vlan. This topology worked bef...
We want to implement Microsoft Clusters over 2 locations. The requirement for MSCS is that the private and public networks for cluster nodes have to be the same. So we are trying to solve a problem like this: the same VLAN100 has to span a DS3 connec...
Dear all,We have IGX 8420 9.1.15 can any one pls tell me how much bandwidth it Utilises for Routing Updates.Also PLs suggest any stable new Version so that we can upgrade. Waiting for ur kind replies.Thanks & regardsSAM
I have 2 offices connected by a T-1 line. One office is unable to receive internet service, so i set up a NAT from one office to the other to allow for internet service to reach the non-internet office. The systems works great, Road Runner ISP provi...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |
User | Count |
---|---|
2 | |
1 | |
1 | |
1 | |
1 |