Hi allDoes anyone know where, if possible, I can download all the Cisco MIBs in one go i.e. in 1 zip file ?Many thanks for any helpKind regardsMarcus
Hi allDoes anyone know where, if possible, I can download all the Cisco MIBs in one go i.e. in 1 zip file ?Many thanks for any helpKind regardsMarcus
I have a 2610 with a NM-4E in it. Right now one ethernet is connected to a cable modem (Toshiba), which is connected to the ISP. Three other ethernet ports go to different LAN segments. I want to get more bandwidth by adding a second line from the...
Hi,Would like to know what will be the maximum number of devices that can be managed using RME 3.5 (Windows).
Can you look over my new config to make sure it looks ok? This access server is an AS5400 with 8 T1 isdn pri lines attached. Its only purpose is to be used a dial-in box to our network. It will not be used to dial out. It has 1 d channel for eac...
Anyone tell me where i can find out the minimum flash and RAM for c3660-bino3s-mz.123-8.T3.binThanks
Hi,Are the 5509 and 5513 AC power supplys compatable? Does thew 5509 AC Power supply work in the 5513 chassis?Thanks,Derek
Does anyone have an timeframe for when Threat Response will be rolled up into VMS?
hi,i have a DHCP server x.x.x.x running in my LAN i want my remote office lan to get IP addresses from my DHCP server.I have applied IP helper address x.x.x.x on the lan of my remote office and on the serial of this office.Still i remote office users...
Hi Guys,We have a customer that has a bunch of 6506 chassis's. They needed dense gigabit presentation so we ordered 6148-GE-TX blades for the switches. We checked the software advisor to make sure Sup-1A-2ge (msfc1/pfc1) could run the correct softwar...
sir i have a 1750 with below configuration and facing a problem like it stops the internet access for the 15 users on the lan which are connected through the nat on the router after reloading the router it again works for a while but stops the surfin...
Dear Friends..Cisco 2621xm will support HSSI Card? any idea ?Thanks and regardsnaga
Dear allI work as an Customer service in ISPI have some client report that they did not take the correct BandWidth in the ADSL connection (SLow browsing and download)they take 512 Kbit Rate and the Download is 5 K byteI trablshoot with them and evry...
HiI have a problem with RAS on my router.When there is an unsuccessful callback from the router, the router is not able to answer the client's call on the same line again for a long time (approx.6 hours).Has anybody a good idea to solve this problem?...
hi, my switching background is a bit shakey. i have 2 simple questions for you guys:1) i have a cat2950 that is configured as the root of STP. it is also the VTP server. i want to make some changes so that our 4500 is the VTP server and ST root. this...
Hi,I have client that is connected to my router with BRI. We use "ppp multilink", so both B channels can be used. My client is the caller site and my router is the called one. My client says that all calls are ended in 120seconds although there is st...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |
User | Count |
---|---|
2 | |
1 | |
1 | |
1 | |
1 |