I want to configure my Cisco 2522 Series router as a DHCP Server for the network. But when i tried to do that there are no commands available for this. Pls tell me how can i do this.I m using 12.0(5) OS in it.Pls help.
Dear Experts,I have a SW-2924C-XL-EN switch.The switch some time could run with the prompt "switch: "However, some time it could pass the POST (as in the end of this message).Do you have any way to solve this problem?Thanks.Nguyen Nhat BinhC2900XL Bo...
Does anyone know if Cisco IOS software that supports IP/IPX W/VIP for platform CAT6000-MSFC2 means that I will be able to have workstations running Novell client and connecting to Novell servers which are located both in the same VLAN and other VLAN(...
I have Cisco 2522 Router. It has bri port(not mentioned S/t or U type), firstly i am confused about this that what interface type it has.I am from Pakistan,in Pakistan external NT1 is used for connectivity(S/T interface).I want to connect my this rou...
I have a 3640 with ios version 12.3.7.T1 Ram is 128 mb and flash 32 mblast night i received this message:Queues messages:*** System received a Bus Error exception ***signal = 0xa, code= 0x1, context= 0x63f229f4PC= 0x6048fed0, Cause=0x420, Status Reg=...
Hi EveryoneWe have two 2600's with an E1 running only data. We have noticed that on occasion we require additional bandwidth but not enough of the time to order a larger line and go to the expense of HSSI interfaces etc.Someone suggested we run stac...
Hello,I need to configure rspan. The source and destination switches are 2950s. The intermediate switch is 3524XL. Can this work? In general, how the rspan works from the MAC/forwarding point of view? Does something have to be explicitely configured ...
Hi...My name is Choi tae young.I'm sorry. My english write skill is very low.My site running the ospf routing protocol."Debug ip ospf event" command excute on the backbone rotuer(7507).Often ouput the event message that "service_maxage: Trying to del...
I have a 1720 with a WIC-1enet, i have the E0 set for DHCP which it is not getting a IP address, here is my conf ,Any ideas? I thought once you got a DHCP address it would show in the SH INT E0 command,correct?Ethernet0 is up, line protocol is up Ha...
One remote router with a T1 to our router and then another T1 from our same router to another remote router.I want to create a point-to-point between the two remote routers similar to putting them in their own vlan. Is this possible and what might th...
HiWe setup two links between out headoffice to branch office using DXX(leased line) connectivity. The bandwidth is same which is 192kbps. The EIGRP protocol is also running on both links. My question is that how to configure routers for load balancin...
Anyone know how to generate a report that will display inactive switch ports? We have cat 6500, 3500, and 2900 switches. About 300 switches altogether. I would like to disable inactive ports.I have CiscoWorks LMS, but I cannot fand a way to us it to...
We've recently upgraded the IOS on all of our Catalyst 3550 switches to 12.1(20)EA1a. Now, on the running config for each port, we see "switchport mode dynamic desirable." Wasn't able to find anything in the release notes for the IOS version. My q...
Hello,I am trying to get a multi-homed architecture goingand am using the following white paper as a guide:http://www.cisco.com/warp/public/cc/pd/iosw/ioft/ionetn/tech/emios_wp.htmThe prolem is that after the router is up for 1 hour, 92% of the Outsi...
We're in a switched environment, running a couple of Cat-6506's on the core and Cat-2980G's on the access layer. We have 8 floors and four Cat-2980G's are daisy-chained on each floor, with the first one upstreamed connected to one of the Cat-6506 and...
