Wondering if a vlan can be in its (protocol is down) status and if so, why, since it is just a virtual interface.no shut doesn't work on this, any other idea other than deleting and creatin the vlan?
Wondering if a vlan can be in its (protocol is down) status and if so, why, since it is just a virtual interface.no shut doesn't work on this, any other idea other than deleting and creatin the vlan?
I have stack of 3750s as access switches, running CSUF within the stack. So there is only one forwarding uplink in the stack at one time. Top and bottom in the stack are connected to a pair of upstream distribution switch as usual.Would it buy me any...
I have a bunch of PIX 515 firewalls that I wish to acces via a straight analog phone line. This way if the box is messed up I can still manage and reboot it without network access. How can I accomplish this on these models. All I have is two RJ45s...
I am trying to set interface packet thresholds and report an alarm or event when this threshold exceeds the limit. Now, for IOS I am using the following line from #sh int fa XX:5 minute input rate 30000 bits/sec, 58 packets/secorrmon alarm 1 lifEntr...
I have a number of locations throughout the country connected together over frame relay, all of which are bridged. (Cisco 1601s) I would like to route these now instead of bridge them. I know how to set up all the routing, but wondered if anyone had ...
I have two 6509's. One running CATOS and the other has the new integrated IOS. If I connect a crossover b/t the switches on 10/100 ports, the CATOS switch shows link and says the port is connected. The other switch shows that the port is down/(lin...
I have one hundred of catalysts 3550 and I would like to access them via Visual Switch Manager.I have also an ITM and a LMS station whose requireJava Plug-In 1.4.1_02.I would like to know if this version of Java Plug-Inis compatible with VSM on 3550 ...
hiWhat will my variance be in this case. I set it to 2 but don't eigrp load balancing across unequal pathshere is the scenario. I have two routers at the lab. Each has two 64K serial links. One serial link is directly connected to the second router...
I have http server access set up on a Router.When the IOS Image was upgraded, for some reason, the Telnet link disappeared from the Router Home Page...What do I need to do?Thnx
Hi allI have cisco 3640 with 2 FEiam trying to integrate with Cache EngineBut i see most of the example shown with 3 interfaceThat means, i should have much 3 interfaceor still i can do with the 2 Interfacestransparent cache is working...when i want ...
Hi,I am trying to find the documentation for "ip host-routing" command (12.2(15)T on Cisco 1721) ?Does anyone know, the purpose of this command ?Regards \\ Naman
I am doing cleanup work on a LAN. I am trying to integrate a local network with the prior hardware from two LANs.I have an ISDN line coming in to a MS workgroup environment. I also have the following hardware:1 - 6781 - 8041 - 3Com 8-port Hub1 - 3C...
Hi,A customer has experienced the problem, his 7206 router can not reboot. It always went to RMON mode even if he reset the register nomber to 0x2102.Here is the error message during reboot:*** Cache Error Exception ***Cache Err Reg = 0xa4005399data ...
I just wana know about CRC erors,wht cld be the cause of crc eroors.I have cisco 1721 router and thr are lot of crc errors.Regards
Our company proceed in upgrading CWRW 1.1 to CWRW 1.5. We tried also to upgrade ACL Manager 1.3 to ACL Manager 1.5. The upgrade installation worked fine, but when we tried to contact ACL Manager, the browser freeze, some java applet messages were pre...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |
User | Count |
---|---|
2 | |
1 | |
1 | |
1 | |
1 |