Other Network Architecture Subjects

Eigrp Variance

I am using Eigrp as a routing protocol in my network.The problem is that variance is not working.I mean if a destination network can be reached from 2 paths whose metrics are within the variance,the network is reached through the best path only.Does ...

Resolved! BGP question

I have have a setup where BGP with AS "X" has received a route from AS "Y". I have to ways between AS "Y" and "X" . How do I get AS "X" to advertise this route back to AS "Y" when it has originated from "y"?I hope you can help, thanks.

About ipx address question !

Ip address is hierarchical address, Then ipx address is hierarchical address too , isn¡¯t it ?

Catalyst 2950SX and SMC switches

Dear all, We need to puchase the Cisco Catalyst 2950SX for uplink purposes with our existing SMC switches. Here are the features of our SMC switches :TigerSwitch 6724L2 Layer2 switch - 24 10/100 UTP . Auto-MDIX, 2 slot option for 2 additional 100FX ...

Latest IOS & Modem ver of 3640 RAS Server

Hello , We have a 3640 RAS Server with Analog Modem Module on our Network for Dial-in users . Below are the IOS & Modem ver of RAS server. Some of the Dial-in users who have the new models modem have a problem of call back and connecting speed does n...

Connecting UXIX Servers To Mutiple 6513's

I have a 6513A and a 6513B connected to each other VIA a trunk. I have Windows OS servers connected to each of the 6513's in a active/passive mode on the NIC. I want to do the same thing for our new UNIX boxes, but everyone tells me this is not po...

Loadbalancing with backup load on 2503 IOS 12.0

Hello all.I try to connect to sides with two 2503-Routers with IOS 12.0 using a leased-line on ser0 and a backup-line on bri0 using a dialer-poolWhen I tried the use of backup load the peoble on the remote side found, that the performance is bad (the...

dialin and dialout thru one BRI

HI all I have c1712.The idea is the next :I want to use dialout thru one B ( DDR - dialer0) if my primary internet connections that goes thru f0 fail . The second B channel I want to use for dialin to Lan network ( in same time , when ddr work - dia...

CMS 3.0 Issue

I have attempted to access my WS-C2950-12 switch using CMS. When ever I attempt to access the web console I keep getting "The page cannot be found". I know that I must be missing something. I need to make this plugin available so that some of the tec...

6509, 48-port 10/100/1000 Ethernet module

Hi,We have 6509 with SE2,MSFC2/PFC2 and SFM2 installed.We want to buy a module with 48xRJ-45 port 10/100/1000 (and we dont want over-subscription)for server farm.What do you recommend?

ethernchannel 3548XL-2900XL

Hi allI have a 2 officesthe distance between this offices are 2Milesso i had run the Fiber cableand terminated with media converter (MC)from fiber to Ethernetnow my network diagram looks like belowinternet--Switch--(mc)---Fiber---(mc)--Switch--client...

CatOS vs. IOS

Also, can anyone tell me the pros and cons for using CatOS vs. IOS on Catalyst 6500?Which situation better suits for either of these?Thanks,Senad P.Net. SpecialistWeber State University

Resolved! About ISDN config

customer asked for user-defined username instead of the default hostname of the router to configure two router connected by ISDN, generally, we configured router like:RA(1.1.1.1)------(1.1.1.2)RB-----hostname RAusername RB pass xxint bri0dialer map i...