my consumer have a 2948G and a cisco 4006 and made a FEC using 2 FE port in every switch,now 20 PC connected with 2948G,2 IBM server connected with ,and a server used for FTP server ,but zhe ftp speed using ftp client on PC to download file from ...
my consumer have a 2948G and a cisco 4006 and made a FEC using 2 FE port in every switch,now 20 PC connected with 2948G,2 IBM server connected with ,and a server used for FTP server ,but zhe ftp speed using ftp client on PC to download file from ...
Hi All Pro. I need your advice on how to route traffic based on Source Network IP on PIX515 and C2500. I am not sure that which technology will be needed. Please help me on it.Thank you in advance.Amnuay
why a route in ibgp can not be sent to its ebgp peer while there is also the same one in igp, do not say "no sychronization" I just want to know why
Hello anybody well familiar with EIGRP/GRE, or QoS too!Notice: I present now some trouble scenario, for which I place just one introductory question, at the end of text. Simultaneously I will do testlab research, planning to perform tests focused esp...
I have a client that has an existing Cisco 2610 with the standard WIC-1DSU TI WAN card. However, they want to switch to cable internet. Is this possible with this module? I cannot find any information on the Cisco website. Is there a module for t...
I have an old, (I use it for testing purposes), 2501 router. I noticed 12.3.6 was released, so I wanted to see if the bug that infiltrated 12.3.5 was gone. I downloaded the IP Plus image and after a few attempts realized the image was to large to f...
7507 VIP4-80+PA-MC-STM-1MMConnect 63 2611XM through SDH Unframed E1,Does anybody can give me a configuration Example?
Hi!We got a solution from our leased line provider call Y-protection:A leased line has to ends, but only one is completely available at a time. When endpoint one fails, number two takes over.Now the problem:Each endpoint is connected to a different r...
Does the OSPF "summary-address" command for external networks support supernetting. For example "sumamry-address 192.100.0.0 255.255.0.0". Also, can you configure a static route as a supernet? For example "ip route 192.100.0.0 255.255.0.0 10.1.1.1".I...
I have an old 1924 and wanted to know if they are NATable and can be used with VPN? Thanks.
Hi,Can someone tell me how I can tell the actual bandwidth available on my Serial interface and its sub-interfaces.I think my ISP is over-charging me.Thanks
Does the OSPF "summary-address" command for external networks support supernetting. For example "sumamry-address 192.100.0.0 255.255.0.0". Also, can you configure a static route as a supernet? For example "ip route 192.100.0.0 255.255.0.0 10.1.1.1".I...
Good Day,I have been requested to connect a WEBSENSE device to monitor Internet traffic going to out PIX's. I have 2 6513's running CATOS, connected via a trunk on the SUP720's. The SUP720's are running in HRSP.The PIX's are connected to port 3/20 ...
Users sitting behind a 16 port 10/100 Netgear switch report slow response or the inability to save documents to a file server attached to a 4006. The Netgear switch is attached to a port that was set forced 100 full. Pings timed out as the packet si...
HelloDoes anybody know how much performance the HSRP-process consumes per subinterface?In my case three routers have to build 14 segments.At the moment only the three vitally important segments are protected trough HSRP.But I plan to make them all re...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |
User | Count |
---|---|
2 | |
1 | |
1 | |
1 | |
1 |