Hi,does anyone know of a good step by step procedure of how to setup vlan trunking between a catalyst 3500 switch and a 6513 switch?
Hi,does anyone know of a good step by step procedure of how to setup vlan trunking between a catalyst 3500 switch and a 6513 switch?
We recently encountered a serious problem with Cisco IOS 12.2(19) and ISDN connections. Our setup was a 7206vxr router with 2 inbound PRIs.When a remote site would fail over to ISDN backup (from frame relay) and call in to the 7206, the connection w...
Hi,Running cisco works 5th edition, with Resource manager 3.4, got around 500 router and switchs in the network.Is there a way to create a custom report as follows:*Device Name*Device Type*Device Serial Number*Module or Modules Type* Module Serial Nu...
Have been unable to start the CW Daemon Manager. I can log into the CW console but process status returns a critical error - 'there was an error getting process details'. Start processes states all processes are running but stop processes states all ...
I have a Cisco 4700 with IOS 12.2(2)T1 with 3 ethernet ports. The F0 port is the local privately address network and the other two Ethernet ports are used to connect to two different DSL circuits, which one is a backup to the other. I would like to d...
Our customer has Cat4500 with 12.1.12c-EW2 IOS. It has VLANs (with 802.11Q tagging) defined and IP routing among VLANs enabled. Is it possible to configure IPX routing among VLANs on this configuration ? Is there any document describing IPX routing c...
Can anyone point me to some examples or Cisco docs on how to do NAT on a Cat6500 with MSFC's....
hi,when looking at a gigabitethernet interface i found that it's experimenting output errors. i was wondering exactly what could cause this and how to fix it. as far as i know having output errors on a GE is not posible wihout having underruns. anybo...
I have a 3750-24TS with EMI image to link 2 FreeBSD run VRRP daemon. I use tcpdump to ensure FreeBSD send VRRP packet out and with real NIC ip for source and 224.0.0.18 for destination; with VRRP multicast address for etherframe source (ex. 0000.5e00...
Could someone explain why it is not possible to terminate a unframed E1 (2.048Mbps) using the NM-1CE1U or NM-2CE1U network module.Surely a channelized E1 card could handle an the above circuit - has a clock source etc?Instead Cisco sell the VWIC-1MFT...
Hello. We have a Local Director 430 with software version 3.3.3. There is a 4-port Fast EtherChannel configured and connected to a Catalyst 6500 switch. We know the algorithm used for distributing traffic between the ports within the channel on the s...
to dynamically associate some IP config. parameters (such as IP route, ACL, ...) to a dialin user, the per-user configuration IOS mode (with AAA server) can be used ;is theis mode possible on Async lines or only on ISDN lines ?
By default IOS switches enable errdisable for link-flap and I have had several instances where this has occurred. My concern is if this where to happen to a very mission critical port.Is anyone aware of any issues that can occur by disabling errdisa...
Can anyone tell me how to find out what ip address has initiated the dials for async calls in the following config, you cant simply do a 'sh isdn act'I have run deb on isdn eve/q931/q921 but this just shows which pri is being used and not which ip ad...
I currently have two sites connected by a 100Mb ethernet link with a 2Mb serial backup. At either end I have a 2600 routers running eigrp although most routes are statically enter at either end and redistributed with eigrp.I have recently acquired a...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |
User | Count |
---|---|
2 | |
1 | |
1 | |
1 | |
1 |