I am trying to get MRTG working on 2950. however there are no logs or png files. Do I need to enable anything on the switch ?Can anyone give any advice ?Kind regardsAndy
I am trying to get MRTG working on 2950. however there are no logs or png files. Do I need to enable anything on the switch ?Can anyone give any advice ?Kind regardsAndy
Can someone tell me why and how the router-id keeps the highest ip, even if that ip address was deleted? I orginally configured an ip at 192.168.1.65. Then I configured another interface at 192.168.1.129. When I deleted the 129 ip address. It keeps t...
Need a little help if anyone can. I have a cluster configured and I can't log into the the manager of the cluster. It just keeps prompting me for the enable password. I've noticed others have had this similar problem, but, they have also not found...
Hello,I have two routers cisco1721 using IOS with IPSEC 3DES features. But, When i Check my serial interface, it dont apears in my config so i have WIC-1T card inteface. What is the problem. The two routers are new.Plz I need Help,
I have 2 networks joined by a T1 with a 1720 on each end of it. I use a W2K server for dhcp and have 2 zones created for each network. One is 10.10.10.x/255.255.255.0 and the other is 10.10.20.x/255.255.255.0. I can't get the .20 network to use dhcp....
Hi,How to user Crystal Reports software for cisco works inventory.Is there a cisco document about this or and other useful document explaining how to use crystal reports.RegardsMee
hello all,i am wanting to do some network performance testing by checking peak load bandwidth across my switch ports.Is there a way i can monitor and log multiple switch ports ? I believe monitoring one port can be done but can i monitor multiple at ...
A local company wants me to set up a router for their office. They currently have a DSL connection. What would be a good router purchase for this setup. There are only 4 machines setup right now (will expand in future).
How come that I have reliability on route 10/255 (sh ip route) and on interface 255/255 (sh int atm ....). How EIGRP calculates reliability?Thanks!
3 routers, R1(s0,e0), R2(s0,e0,s1,e1),R3(s1,e1)R1 s0------R2 s0 (run OSPF)R1 e0------R2 e0 (run EIGRP)R3 s1------R2 s1 (run OSPF)R3 e1------R2 e1 (run EIGRP)there are some other routers connect to R1 and R3, run OSPF or EIGRP between them, we don't c...
R1 s0---OSPF---s0 R2r1 has two loopbacks, 192.168.1.0/24 192.168.2.0/24redistribute the two lookbacks to OSPF, right now R2 get two external OSPF routes with SAME metric, how can I give the two routes two different metrics?I tried the below way, it d...
Hi,I have a Linux based server that connects to one port on my 3550 with 4 IP addresses. I have found that some (1 or 2) of the IP addresses are down whilst the rest are still accessable. This happens at an erratic rate with no pattern.From the switc...
Hi,I have a cisco router running IOS 12.2(8)T5. I have created an access-list to restrict the SNMP access and executed the following commands to enable SNMPaccess-list 1 permit host 192.168.9.47snmp-server community public RO 1But it is not respond...
After updating SW 2.2 running in a solaris WS to the latest SP (SP2) some processes fail to run:EssentialsDbMonitorDIServerCmfDbMonitorIcServerNo success trying restarting them.The message I get:Application failed or was registered incorrectlyAny ide...
Dear All,We have a RAS setup at our Central Office.To setup the RAS network we are using Cisco 2514 router with 8 async interface.To each async interface we have connected external Dlink modem.Users were able to dial-in from remote location using win...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |
User | Count |
---|---|
2 | |
2 | |
1 | |
1 | |
1 |