Other Network Architecture Subjects

IDS MC 1.2 and deployment problem

Hi i want to deploy a signature configuration from IDS MC logs say task deployed successfully but when i connect to ids i cant see that signature configuration has been changedAny thoughts will be appreciatedIDS Version is 4.1.1 S58

Cisco Catalyst Switch 2948G..Urgent ..pls help

My task is to manage Cisco 2948G switch using NMS.I am supposed to use CISCO-STACK-MIB.I just need the following hierarchy info of Cisco 2948g switch.Please tell me the number of components in eachChassis |-->Slot |-->Module |-->Po...

CW2K on Solaris-Daemons.log errors

My daemons.log is over the size limit even after backup and reboot. I am getting some of these errors:ERROR: CORBAREGISTRY:Unable to connect to ManagerControl object. Reason: org.omg.CORBA.BAD_PARAM: minor code: 0 completed: NoIt is also full of...

RME-Inventory- Device stays in Pending mode forever

Hi,We have CiscoWorks 2000 with RME 3.3 running on Solaris 2.7.When I am trying to add a device using RME, the device stays in pending mode for ever. Has anybody experienced this before?. It was working fine before I reinstalled Solaris and Ciscowork...

EIGRP and Loadbalancing

Hi Guys,i got a questions regarding loadbalancing on Cisco routers. say, I have two locations( SiteA and SiteB) connected by two E1(LinkA, LinkB of equal cost) Links and i am using load balancing on these two links. i am using VoIP between Site A and...

Spanning tree

Hi, If I have a single(default) STG configured and later on introduce a new Layer 2 switch and connect it to the existing LAN...Will the introduction of the switch bring down the entire network ??Will the switch automatically learn the topology and ...

FRSM Ports Monitoring

Dear AllIs there a way to monitor and draw a graph for the utilization of the FRSM ports, on the MGX 8850??From my point of view that dspportcnt gives the immediate utilization ....Thanks a lot

Resolved! Remote reload of a 4006

Folks,Has anyone the command to reload a Cat 4006?Sorry if this sounds a bit simple but i can't find the command in the help facilitythanks in anticipation

OSPF on a 828 GSHDSL Router

Does anyone know if its possible to be able to use OSPF on a 828 router?

Retreive Mac adress table from command line

Hi,I would like to know how to retreive (in a text file) the mac adress tables from many (100)remote switchs using a command line.Thank you for any helpPatrice

Cisco 2610 12.3.5 NAT Bug?

So... I've been running many versions of IOS on many routers and never had any problems with CBAC Firewall, NAT, public IP on the outside, private range on the inside - fairly straightforward. On this particular router, I've been running software wi...

How can i upgrade the IOS on 7513?

Dear All, please give me suggestion how can i upgrade the IOS in 7513 i hv my laptop with me but i can't ..pls l;et me know the procedure.rgdscisobuddy

Cat3550 & MAC access lists

Hi everybody.I have catalyst 35550 (c3550-i5q3l2-mz.121-19.EA1) with configured simplest MAC access list attached to L2 interface:mac access-list extended xxx deny any any!interface FastEthernet0/2 switchport access vlan 20 switchport mode access n...

Problem with XDCMP and VLAN

Hi,I am migrating a FDDI bridged network into a routed one, for that a 6509 with sup720 has been installed. Everything seems to be OK until i tried to browse the XDMCP servers available, none appear (it should list dozens of Unix servers).I assume t...

Cisco Switch 2950C

Hi to all,I have 4 Cisco Switch 2950C Switches to be installed in a cabinet.What type of cable do I have to use to connect each other? Please be advice.Thanks

Other Network Architecture Subjects

Forum Posts

IDS MC 1.2 and deployment problem

Cisco Catalyst Switch 2948G..Urgent ..pls help

CW2K on Solaris-Daemons.log errors

RME-Inventory- Device stays in Pending mode forever

EIGRP and Loadbalancing

Spanning tree

FRSM Ports Monitoring

Resolved! Remote reload of a 4006

OSPF on a 828 GSHDSL Router

Retreive Mac adress table from command line

Cisco 2610 12.3.5 NAT Bug?

How can i upgrade the IOS on 7513?

Cat3550 & MAC access lists

Problem with XDCMP and VLAN

Cisco Switch 2950C

Get ready! Great things are coming to Cisco Community

Have your wish for humanity broadcast into space by George Takei!

Host unable to access remote Host from behind ASA / Router

Re: Cisco device discovery

Re: help with log in router cisco ASR1001-X

Switching

Re: Ppoe automatic default route. &IP address

Network card interface lights

Real multicast uses on the public internet

reboot after short power outage

CBS350-48Xt-4X missing UDP Relay and IP helper-address

When should we use MAN instead of LANs with WANs?