Other Network Architecture Subjects

My ISP gave us a cisco router that does a bridging with a range of public ip @'swe have a range 217.76.98.23/28 on one of the interface while the other is configured with a modem now I would like to know how they have configured the router because we...

I need help troubleshooting this. This is a fresh install with service pack 2 loaded. I'm using an HP2200 with a built in jet diect card. First, I added the printer by creating a new local tcp/ip port with no luck. Not sure on why it is failing, I se...

this is on a 3725 router, assume that the 10. addresses are public and the 192 addresses are private.int fa0/0 - internet sideip address 10.1.1.2 255.255.255.252int fa0/1 - lan sideip address 10.1.2.1 255.255.255.224int fa1/0shutint fa1/1shutI have p...

I am looking at bringing 5 T1s from my isp to a Cisco 3640 and bonding them together to create a 6 meg connection. Would I use PPP Multilink configs for this type of solution and if so, anyone have a documentation?

I have OSPF running on the MAN/WAN. One of the OSPF links is a 100mbps connection from a 6509 to a 7206. The 6509 MSFC is the active router for the MAN. I have a point-to-point vlan for the connection from the 6509 to the 7206. The 7206 routes to th...

what card i should use for 7206vxr router to get 4 Mbps bandwidth on a single interface, can I use PA-4T for this purpose or some other card.

I have a cluster of Cat 2950's running 12.1.19 EA1 that are running out of memory after 2 or 3 days running. It seems they are running out of processor memory first, then I/O memory. A show mem dead shows a LOT of dead processes still in memory. I'm ...

We have this 2600 router and 512 K ISP bandwidth...running a c2600-i-mz.121-19.bin train.For the past month we have been having high input rate on our serial port dispropotionate to the Tx rate Serial is sometimes Rx 250/255 and Tx 30/255Considering ...

The port 15/1 which communicates the catalyst 6509 Switch with its MSFC, is in trunk mode, but, should it in portfast enabled mode..?

Hi Folks, I've got two WS-C3750-24-TSS, and two GLC-SX-MM.. but no cables.. I ordered some CAB-STACK-1M= cables, but those were the wrong ones.. could someone please tell me the reference on the cables for connecting the GLC's ? Thanks in advance, ...

Q:what is the difference between G2/9 and G2/10,best regards!Platform:Cisco6509sup720 IOS Version 12.2(14)SX1interface GigabitEthernet2/10 no ip address shutdown switchport switchport access vlan 1200 switchport trunk encapsulation dot1q switchport m...

Hello ,I have a little problem with a connection over a 801 to a central Cisco 2620.When I ping from my PC to the remote network in the central or the 2620, the 801 connected to central, but no packets came back.The Ping from the 801 to the central w...

We have a 2600 router running a flash:c2600-i-mz.120-3.t3" train...the configuration register for the same is 0x3922...cant reset it back to 0x2102 followed the right proceduresWhat does register value of 0x3922 stand for and how do i reset it back...

Hi, i'd like to migration my network,and i musto to divide in two site.I tried with virtual-link in OSPF but it's no good idea.I don't want use the bridge for the tranpsort,nayone have some ideas?????ThanksRegardsRoberto

Hi, I've got a very weird problem with my 1721 router (16M Flash, 32M RAM.WIC-1Enet, WIC-2T,enable NAT for Internet(go through WIC-1Enet)): It will automatically restart every 10 minutes. Here is what I've got through the console port(before it resta...