I would like somebody to explain me why I can assign an ip address to every fastethernet port of the layer 2 switch?What I know is that I can assign an ip address to vlans and not to the port directly.thanks
I would like somebody to explain me why I can assign an ip address to every fastethernet port of the layer 2 switch?What I know is that I can assign an ip address to vlans and not to the port directly.thanks
Hi All,I have a leased ISDN connection. When I try to transfer file larger than 1Mb, it takes more than 1 hour. If I initiat continous ping during the file transfer of the same file, it takes very less time. Files with size less than 1Mb is transfere...
i have next situation-Router 2610!class-map match-all tcp match access-group name tcpclass-map match-all ftpserver match access-group name ftpserverclass-map match-all webserver match access-group name webserver!!policy-map internet class webserv...
is it right to say that 1. if a newly inserted switch vtp mode is either client or server, it could caused network problems if the configuration register is higher than the existing?2. that the vtp revission number doesnt have anything to do with inf...
I need to direct all dhcp request originating from clients attached to a particular switch 3548 to a particular DHCP Server ........ on the int vlan 1 i see the command ip helper a.b.c.d has anybody used this successfully on a switch ???
Hi,Catalyst 2950SX-24 doesn't implement 802.1s at present. Will cisco implement it in the future?Thanks
As I can see, The VACL feature is supported in the latest native IOS for SUP1/MSFC2 & SUP2/MSFC2. But can the latest IOS for SUP1/MSFC1 support this feature? ThanskRegardsJeffrey
Hi,I've been work in Japan.The ISDN switch type, configured by "isdn switch-type" command, in Japan is just "ntt" for BRI or "primary-ntt" for PRI.Now we are going to install routers on some countries, however I can see many kinds of ISDN switch type...
I have RME 3.4 and I'm unable to update the Cat6000 package. version 1.6 of the package is currently installed and RME tells me 4.0 is the current version. I have sucessfully updated all the other packages. I get this error messageCat6000(4.0) major ...
Hi All,I'm upgrading the flash memory in an old 2503 I use in a test lab. It originally had 4M flash, I put in 2 new 8M modules (MEM-1X8F). Now, it starts in Boot mode with this message:ERR: Invalid chip id 0x80B5 (reversed = 0x1AD ) detected in Sys...
Hi,As above, how can i tell if a switch has got a route processor? or can be a MLS-RP?
Hi,What kind of files I need to backup for my C6500 switches + MSFC2 and PFC.Also I have 20 3550 switch and some of them was stacked.Do I need to backup all switches configuration file a stacked group.ThanksRaymond
I'm troubleshooting a Cisco 1720 with Version 12.2(8)YN IOS. Is there an IOS version with the ip route-cache flow command available for the 1720 ?devans
Our routers have a pound signs at the end of the prompt due to the privilege setting in the routers config (level-enable 3 and debug 4). This has caused many problems with Ciscoworks2000. My question is If a router is capable of producing a pound si...
I have a question about SDLC DISCONNECT, this is the basicquestion through ...I understand that the router pass through DISCONNECT onlywhen the router received it from HOST and the router NEVERsend DISCONNECT generated by the router itself.That is, t...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 01-22-2025 07:00 AM | ||
| 11-14-2024 09:33 AM | ||
| 10-24-2024 11:51 PM | ||
| 10-20-2024 10:52 PM | ||
| 09-26-2024 02:28 AM |