Hi, I deleted my Cisco 800 series router IOS by mistake. Now i cant connect to the router. How can i reuse or recover the ios.
Hi, I deleted my Cisco 800 series router IOS by mistake. Now i cant connect to the router. How can i reuse or recover the ios.
HiToday i was configuring Cisco Catalyst Blade Switch 3120x and after upgrading the IOS 15.0(S), I factory reset the switch to have new configurations. While setting the enable password. I faced the below errors. Please suggest some solution.Enter yo...
Hello Guys I am performing a copy operation from the Bootflash of the switch to the tftp server Is there any way by which I can stop/interrupt the copy operation in between
Hi support team, we have problem on our cisco router 3945 router, the ios file is deleted by accident. 1. is their any way to recover it? or2. i have backup of the configuration but no ios where can i donwload ios of this product? thanks in advance ...
We buy An ISE Device to Relace the ACS to manage the network devicebefore this ,we use ACS to manage the Network Device. And define user access the device's level Eg some user only use "show " some user can use "config" .i want to know How to use IS...
All sites have an internet link and a policy shaper applied on WAN link.we have a GRE tunnel created from the site to HQ70 percent of the traffic is via physical interface (direct to internet) remaining 30 percent of the traffic is via tunnel (inter...
I'm looking at Power Supply PWR-C1-715WAC. The Input current is 10-5 A. So does that mean 10A for 120V? If I have 2 of them, does that mean 20A?
I have the following network (map below). When the T1 is operational DHCP clients at the remote site in VLAN 1 (10.10.10.0/24) work as expected via the ip helper on the 'Site Router'. However, when there is a long term failure of the T1, clients can ...
Hello,is there a possibility that I can run the show run command to show all but not the interfaces? maybe: sh run | exclude ...Thanks
--Update--I formatted the flash card on the C6503 in disk1:Tried reading the disk in my Linux PC it would not mount said unknown file system.Formatted the disk again in the C6503 and then copied the old code from disk0: to disk1:Tried reading the dis...
Hello, There is a very high value of SRTT of 1250 and RTO 5000 although Q value is 0. What would be the possible causes? Any one have any solutions for the same. Thanks
Hi,I am using one Switch (Say SW1) as NTP source for other switches (Say SW2, SW3) and it is working fine. SW1 gets time sync from a Router.I have one more network device i.e. IPS and I have have given SW1 as NTP server IP in the IPS.Now how do i ve...
I m configureing ospf on two router which are directly connected on ethernet segment.but not creating neighbour relationshipgeting following outputP5#sh ip ospf neighborNeighbor ID Pri State Dead Time Address Interface3.3.3....
My company is a relatively small enterprise (about 800 people scattered across 45-50 branches) and we are planning on setting up a periodic failover/redundancy testing schedule for our routers. Basically, we want to test the secondary WAN links at ou...
Hello,I'm trying to unterstand serial interfaces and serial connections.There is a Serial WAN Interface Card, for example the WIC-1T.For what do I use that card?When I have DSL connection, my router only has an Ethernet-Interface, which is connected ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
01-22-2025 07:00 AM | ||
12-30-2024 06:12 PM | ||
11-14-2024 09:33 AM | ||
10-24-2024 11:51 PM | ||
10-20-2024 10:52 PM |