I try to connect connect router serial 1 to another router serial 1 on Cisco 2620 routers.Is it possible to make both interface up ? Do i need to set clockrate ?Thanks
I try to connect connect router serial 1 to another router serial 1 on Cisco 2620 routers.Is it possible to make both interface up ? Do i need to set clockrate ?Thanks
Hi,,, I have problems with de Callback process. The debug ppp cbcp show the messages:01:24:40: As70 MCB: Initialize01:24:40: As70 MCB: Flush01:24:40: As70 MCB: Start01:24:40: As70 MCB: Callback not authorized for this user ale01:24:40: As70 MCB: New...
We have a 2950T switch connected to 3550 12T switch.On the 2950T switch the 100BT ports are used for uplinks from other switches catalyst 2924xl. PC's on the switch FTP to server on the 3550. For a get they have speeds of 5000-6000 bytes per seconds...
Hi all,I'm trying to figure out a way of allocating/prioritising bandwidth on a router that connects our network to the Internet. Id like to for example give 60% of the bandwidth to HTTP/HTTPS, 20% to a VPN link, and the rest allocated on a fifo bas...
Hi,Can someone give details of ports used by Kaaza software.TIAMurthy.
my customer has a running catalyst 3550.he asked for me to check the GBIC type by console. is it possible to check it ? if yes, how to do it ?thanks
If I have a network setup with an ip address schema of 10.1.x.x /16 and I decide to create vlans on 4500 series switch to make best use of my ip addresses, it will give me an overlapping error with vlan 1when I configured my additional vlans ip addre...
Hell-o,Have two 2501 series routers for our WAN connection. I want to run IPsec on the T-1 connecting these two devices. Can you please tell me what image upgrade will accomplish this task. Presently running 11.2.TIA,Gary
Hi,I've read a few of the comments about multi-homing an Ethernet interface, but I can't seem to get to the bottom of the issue that I'm having. I'm attempting to add a third IP address to my Ethernet0/0 interface. In my config I've the following:i...
HiI am trying to implement load balance between two firewall and found this diagram from cisco website. I just wonder why L2 is needed. What is it for?L4-----L2----F/W----L2----L4 | \ / \ / | | \/ ...
I am looking at a proposal that will use a 3550-24-EMI switch at the core, which in turn will connect up to twenty remote sites (over 10mb LES circuits). Each of these remote sites will have maybe two or three vlans. at each remote site, I can eit...
I am having a problem with my remote site utilizing the static routes from my main site (both are 7204VXR). I am using OSPF and statics and believe the issue lies with my remote site seeing my main site as a type E2 as well as the static addresses. I...
Hi all,For dial up users to the Cisco router, I can use local authentication command "username xxx password xxx", TACACS+, RADIUS. Are there other methods? There are only for 8 dial up users, I would think local authentication will be the easiest a...
I did not set up any etherchannels on my 6509. However, the output of "show config all" displays the following:#port channelset port channel 1/1-2 488set port channel 2/1-4 489set port channel 2/5-8 490set port channel 2/9-12 491set port channel 2/1...
Here is the scenarioWe have 2 LAN's connected via DSL modems over an ISDN line.Just got 2 2620's with one ethernet and one serial interface. I want to roll over slowly to the new scheme as I have some apps to test and a new NT domain to create and I'...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |
User | Count |
---|---|
2 | |
1 | |
1 | |
1 | |
1 |