Other Network Architecture Subjects

I have c2950 switch, and I am unable to find any tool to tune and configure the device. Does anyone know what software I can can download from this site? I am currently experiencing problem with the switch, thank you.

Cisco gurus:I configed slb on two 6509s (native IOS, version 12.1(12c)E5). The performance is disappointing. The traffic to load balaced servers is about 4M/s. Previously, cpu load was less than 5%, now it's 30%. sh run sometimes takes 10 minutes to ...

I am not very well versed in frame relay and in trying to troubleshoot some speed issues at our remote locations, I have the following questions.I am trying to understand the specific of the frame relay circuits we have installed for our remote locat...

I have 5 Vlans (including Vlan 1) configured on a 4507r and 3550 switches. Vlan 2-5 are configured with the cable-range and AppleTalk zone. Using a MAC computer, I am able to see the zones I created as well as access servers belonging to these Vlans ...

hicustomer plans to upgrade to 12.3 butfaced to dilema which versions of IOS will need to install.1 or .1ai didnt find release notes for .1a on the Web ?any hints will be welcomedthanksJYP

Can I use these 2 c4k modules for a new project with c4507R and supIV or should I consider them as old modules ?WS-X4232-GB-RJ—Cisco Catalyst 4500 32-port 10/100 (RJ-45), 2-Gigabit Ethernet (GBIC) ModuleWS-X4302-GB—Cisco Catalyst 4500 Gigabit Etherne...

I am trying to configure integrated digital modem via ISDN-PRI link on a cisco 3660 router. Following is the basic configuration;( using NM-30DM and NM-1CE1B modules);hostname Router!!modem country mica united-kingdomip subnet-zero!isdn switch-type p...

I'm attempting to configure PPPOE on FE interface on Cisco 2621XM to non-Cisco DSL CPE. I have the sampe config from Cisco's doc, but I am not sure about the dialer pool and dialer-group commands and what they reference. This router also has ISDN i...

Hi all,we are looking for management software and tools to manage a small LAN network - 3 sites, around 8 switches 2900 - 2950, and 2 cisco pix / 2 cisco aironets. Would the cutdown version of ciscoworks be the way to go - we want the ability to see ...

my core switch is C4006 and edge switch are 3548 switch and 2950 T-24when I implement multicast Service , the 2950T-24 seems normal but the 3548 switch seems slowly , I have enabled CGMP on C4006 and 3548 switch (include fast leaving )Why ??

Which RMON Agent License for Catalyst 3750 must I order?Is it available?Thanks and regards

I have two PRI E1 connected to two gateways (3745) with MGCP. The layer 2 is bouncing from "WAITING ESTABLISHMENT" and "TEI ASSIGNED". I enable debug isdn q921 and debug isdn error, the only message I get is :ISDN Se1/0:15 SERROR: nfas_T3OOS_timeout(...

Hi ,we are using as5300 and 6 E1lines (2E1 are down) , sometime we see on our mrtg graphs that explain modem use great than ppp use about 10-15 numbers.i checked our controllers, didn't have any frame loss and our E1 didn't flapping , anybody advice ...

What equipment do I need to be an ISP??? The main thing is what device do I need to autheticate and accepts dial-up clients?? What are the current equipment use by ISP? Thanks.

how do u enforce the inbound and outbound (with respect to a vlan) traffic via the active leg.cos when I perform a traceroute from external to the vlan(with hsrp configured), it always via the standby leg to reach the vlan. and the outbound traffic i...