Hi,I need to lock one of the Ethernet interfaces on a router to a specific MAC address so only one device is allowed to use it. I haven't been able to find any way in which the ACL enables filtering on MAC address.Any ideas please ?Thanks.
I have a cisco 3662 router with 2 WAN ports and 2 FE portsI have connected two isps on my WAN ports to FE 0/1 using route-map command successfullyBut I when try to connect a RJ-45 cable form a ADSL ATU-R modem to my cisco 3662 FE0/1 port , I have p...
hi, we've got a 2 port Layer 2 etherchannel between two 6509's.I need to add additional ports to the etherchannel as it's starting to drop packets.The question is, can I do this live without the existing ports blocking?thanks,Daniel QuinlanNetops - ...
I have a customer who wants to have users connect to an as5300 which has a t1 connected to it, then be able to dial out to a remote site. I guess the as5300 would be in a sense a modem pool. Can the as5300 do this and if so does anyone have any confi...
Trying to put together some software to report on utilization of servers for a customer that does not want ITEM. The problem I am running into is that I do not seem to be able to get the Call Manager server running 3.2.2c to respond to snmp mib walk...
Greetings everyone,DFM 1.1 reports discovery error due to an incorrect community string. I've corrected the community string and cleared the alarms but discovery still does not work. It seems to insist on using the old string.Running CWLMS-2.0 on a W...
Hi guys and gals,I'm trying to figure out how I can connect my 2514 serial port to an external 56K modem. I've found a few cables, which convert DB60/DB25. If I'm not mistaken, the DB25 will be the DCE and the DB60 will be the DTE. Herein lies the...
I would like to know if catalysts 1900,2900XL and 5000 stand Rapid STP.I have to implement this feature in a customer and I did not find anything on Cisco pagerelating this feature with these equipments.Thanks,Antonio
Dear All,According to SAFE architecture notes, “Avoid using VLANs as the sole method of securing access between two subnets" Does this mean that instead of assigning the router to do the routing between VLANs I have to assign the FW to isolate betwee...
HiI'm doing some tests and labs on my own and I've got a single 2501 router and I wonder if there's some kind of mediaconverter or transceiver for the Serial port on the router. I wish to be able to directly connect to a CISCO 3512XL switch through t...
Hi! I installed the ciscoworks2000 edition 5.0 on my server.But my ciscoview can't open any device.It show me like this "resulting class definition does not exist on server! com.cisco.nm.cvw.devpkgs.catqdm.descriptorincompatibility may exist amon...
Is there any good cisco link where I can learn about the design and configure aspects of Cisco 7206VXR and Cisco 3745 products for both data and voice.
I am designing Network Management Networks and I need to know how much bandwidth I will need to supervise my devices.The devices are routers and switches.The NMS are Cisco WAN Mgt and Cisco LMS.I usually have two routers and 4 switches per site.Does ...
Oh my god!! I'm stuck in ROMMON> mode on my brand new 4006 and I don't know how to restore it? This is what I'm seeing...rommon 14 >dir bootflash: File size Checksum File name 4118704 bytes (0x3ed8b0) 0xed1d46d7 cat4000.6...
Scenario:What I’m trying to do is setup a layer1 to layer 3 connectivity between 1600 T1 router and GSR DS3 line card (6DS3-SMB line card – 6 port packet over DS3) using ADTRAN mx2800 MUX (T3 to T1 MUX) in between. Here is the Cisco link for line ca...
