I am trying to find out which TCP & UDP ports need to be opened on a PIX to allow Net Registrar (3.0 or 3.5) to work.
I am trying to find out which TCP & UDP ports need to be opened on a PIX to allow Net Registrar (3.0 or 3.5) to work.
I am trying to upgrade my IOS on my 1605 router. I seem to have done it but whenever I boot the router, it boots into boot mode (ie, Router(boot)>). How can i get it to boot to flash??
Is their a special syntax to use so that from a remote location via an internet web browser i can retrieve a page from a server that is on a NAT'd isp.something like http://xx.xxx.xxx.xxx (being the global ip) and then the local NAT ip 192.168.1.2 so...
Policy routing is configured on a 7200 router and applied to a Serial interface. There are three classes defined, one being a priority class. What effect will configuring WRED (wth default settings) have on the priority class?
I just passed my CCNA about a month ago. Now my director seems to think I know everything there is to know about configuring Cisco routers. Please forgive the dumb questions.I am trying to connect a 7206 router to a 2651 router w/ 2 T1s.The 7206 is ...
I am looking for an application that can auto-generate a topological (visual) map of my LAN's switch fabric? Any suggestions?
i want to totally close port 23 on the serial of my router...vulnerability test shows it is open though i have already denied it in my access list...thanks a lot
We recently upgraded to a 7606 with an MFRC in our core. Everything routed through was successfully permitted to leave the LAN into the WAN. However, all directly connected networks were not permitted access to the WAN.There was a line readingIP Br...
I need to know what software to use to get into my router to configure it.Is their a file that needs to be altered on my LAN internal machine. I am new to this but i know what it is i need to configure just dont know how to get into the router.
Does there exist an application that can automatically generate a visual representation of my network. My network is basically a couple hundred switches which I'd like to see a topological map for. Is there anyway to auto generate such a map?
I am wanting to find the cheapest route to gettinga cisco router up at home. Currently I have a DSLmodem and would like to put a router behind that.My question is which router could I go with?I was thinking about the 827 which has the DSLmodem but si...
Just upgraded two CiscoWorks with the CDOne ver 5 and I am seeing the same problem on both. Running on Win2000 server.I installed CDOne, RME, CM, DFM and then VHM.It seems that once I did the last, I am getting the following in the ANIServer.log:mai...
I am Using BadBlue to run a peer to peer server inside a LAN that is NAT'dI need to know how to tell the router to do port forwarding to my ip. It works fine inside the LAN but external remote machines cant get through to my NAT'd ip.I am using cisco...
Hello everyone, I'm going to post this in this forum fist because it has to do with packet prioritization over a full meshed VPN topology. Heres the question ..We have a client that has three sites with 2600s and one site with a 3640. They conne...
How does a router determine which interface to use as a source interface for ntp if a interface is not specifically put into the config ?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
02-20-2024 07:45 AM | ||
02-15-2024 09:08 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM |