Other Network Architecture Subjects

Could you help me the following question?What is SNMP MIB _________a. Stores data reported from all nms-monitored stations.b. Stores monitored variables and variables that controls operation of a single nms-monitored stations.c. Stores configuration ...

Are other people having problems using Hyperterm with Windows XP to configure cisco routers and switches? I got a new laptop and I am having problems with Hyperterm. It connects up fine but the up arrow does not retrieve the previous command correct...

Hi ,We are trying to setup a Dual core redundant network. We currently have two 8540's forming the core layer and 6509;s forming the distribution layer. What we are trying to is to have a fully redundant core.Our current design has the two coresss ...

Here is the scenerio:We have four cat 5509's all with the same configuration (except IP addresses) all trunked together. The version of code is 5.5(7) with sup3 cards. Periodically one of the switches will fail between 3:45 am and 5:15 am. The sam...

Hello,I have a 3524xl switch (IOS 12.0-5WC5) which worked well until today.All ports belong to a vlan (switchport access vlan xx) except port number 8 which uses just vlan 1.All the non vlan 1 stopped working (leds off), sh interfaces says:FastEther...

Is it possible to push out a new or modified ACL template to a specific network class without making changes to them individually? The problem is when I attempt to schedule a download in ACL Manager, it will only send a job to modified devices. Well,...

Is there a way to automatically synchronize the configuration between two HSRP routers? TFTP would work fine if there was a command that you could issue that would leave the HSRP configuration alone. Obviously this is a problem because you end up wit...

I'm trying to configure a circuit between an DS3 atm port and T-1 serial(8 port ) on 7204 with IOS 12.2(7) .So, I want atm port enacapsulation as AAL5MUX FR-ATM-SERV on DS3 portBut that option is not available under aal5muxAvailable options are :ip ...

We recently had a DDos attack on our network that flooded our network with UDP traffic taking our network and internet connections to a crawl. After this the effects were that random clients suddenly took up to an hour to login. We have 2 Cisco Cat...

Does anyone know whether a cisco 803 router configured for dial on demand can have a second dialer string configured so that if the first number it dials, FAILS... Then it will automatically use the second dialer string to connect to another router. ...

It seems that Cisco 4006 supIII and 4507R don't support CMS for the management.Is there a planned roadmap to implement it inside a new IOS in a next future ?

I have a problem with my backup .have you an idea ?My backup is ok when i remove from my config : 1 the default route with my dialer 1 2 ip nat inside source list 1 interface Dialer 1 overload I have this message NAT: dialer not up for Diale...

Hi, i got this issue, and find no answer.. can somebody help me?, i got 2 internet isdn lines of 126K and i want to mix 'em to make one 256K internet on a 3640 router, can that be done? if so.. please answer me, any answer is welcomeThank youFederico...

Hello,I am using 1 7200 router and 2 isp's. I am not able to use bgp (cause 1 isp won't allow it ...BS) so i need to do this another way. How can I do load balancing and fail over on a single router going to to different isp's ? Thank you in advance....

Dear all, I nees to span multi-FE ports (located on different slots) to Gigabit ethernet interface (port on WS-X6408-GBIC). I would like to know if their is any performance impact on the 6509. From the following site http://www.cisco.com/warp/public/...