These things fill my log and I can't see anything else. Are they something I should be concerned about? Can I kill them?Thanks.
These things fill my log and I can't see anything else. Are they something I should be concerned about? Can I kill them?Thanks.
Hi - I'd like to find out what your subscribers are currently using to create proof of concept network design prior to implementing a new system or changes to an existing system.
I'd like to known the maximum length of the BGP Update message
Hi,We have an AS5300 router with an 10 Mbps ethernet interface. Currently the ios version running is 12.0(7)T, IP Plus feature set. The problem is that the ethernet dosent support for full duplex settings. What ios version supports the full duplex op...
I am having trouble finding information related to the following messages recorded in the diagnostic logs of a 3548 switch. %Lineproto-Cluster_Member_2-5-Updown %Link-Cluster_Member_2-3-Updown
How do configure a port on a 2950 switch to not be a trunk port under any circumstances? Will issuing switchport mode access and then switchport nonegotiate for the interface do the trick?Thanks
I am using the following config on my 3600 series router to provision DSL customers. Is the protocol PPoE or PPoA?atm pvc 33 1 33 aal5ciscoppp Virtual-Template1interface Virtual-Template1 ip unnumbered FastEthernet3/0 ip mroute-cache peer default ip ...
I am trying to replace a TDM with routers, the problem I have is that the mux channels are transparent to any framing Tx/Rx by the connected device, in my case Telemetry units running MODBUS. I can't find a way of running Sync data on a router where...
Can anyone point me to some generic step instrcutions for configuring a POS (packet over SONET) interface on a Cisco 7513 router? Thnx.Blm
Hi.I have to configure LLQ and compression on frame-relay subinterfaces and PPP on a Cisco 7500. Is it possible?I´ve heard that "fancy queueing" and compression cannot be used together and I don´t know whether this could mean that LLQ and compression...
We have several routers running OSPF in area 0. These routers are redistributing static routes pointing to remote networks belonging of each of them. Ok all routers know remote networks of other routers by OSPF. We have been testing and if you shutd...
I have the task of setting up an 804 Cisco for despatch to the US and getting it to talk to a primary I/F on a 3640 in the UK. I have ordered an Ni1 interface in the US. I am concerned as to the differences between the 2 ISDN interfaces. I am aware t...
I would like to know if is it possible to install lms 2.1 and ipm 2.4, aclm 1.4 on the same machine. The machine is a pentium III with 1.5 ghz of processor and 2 gb of ram. I tested this configuration with old version but not with the new version.
What exactly is the importance of the native vlan on these switches , tried to get a understanding by looking across CCO but it still isn't clear to me . Should it be left in vlan 1 or should it be changed . What are the pro's or cons of leavi...
About 1 month ago, I started to get these messages logged on my console:%AMDP2_FE-3-RXOVERFLO: FastEthernet0/0 Rx FIFO OverflowThe configuration has been fine for 16 months with no problems. When these overflows occur, the input errors on fa0/0 incr...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |
User | Count |
---|---|
2 | |
2 | |
1 | |
1 | |
1 |