Other Network Architecture Subjects

I have enable PBR on one of my interfaces of 7513.which decide on basis of source IP block and chosse next hop. My question is what will happen if next hop is unavialable (down).will it go to alternate hop as decided by BGP.( I am running BGP, OSPF i...

Hi all, I am having multiple internet providers and running BGP with all of them. Traceroute packets are ping packets with incrementing TTL value. I can know the forward path from my client to the destination i.e ping request path. But ...

I am new to Cisco command line, so please excuse the basic question. I am working with a Cisco 2620 w/ IOS 12.1. I want to configure a static (default) route. I have tried doing so using the IP Route command, but when I do a SHOW IP ROUTE, it doe...

Here's what I want to do:I've got a core router with about 60 sites hanging out of it with HDLC links. I'm want to use ISDN for backup, run dialer watch at each remote sites so when a route dissapear the remote site will initiate DDR, but I would als...

This particular network design is a simple hub and spoke configuration. The hub has two remote offices connected to it via leased lines (full T's). EIGRP is the routing protocol used and the hub is also the NTP master. Both serial interfaces on the h...

does anyone know how to connect directly, via dbreader/dbreader.html or isql, to the rme database ?which password has the dba account ?i will try to get detail information from the inventory, which i can't get from the normal reporting tools.thank yo...

Hi,I have one 128k link thru VSAT(link#1) and one 128k link thru local exchange(link #2). I want to configure load balancing in such a way that1. I want my link#1 to be active only when the traffic on link# 2 reaches 60% of load.2. After the link#2 ...

Hi AllGot some performance issues.If I copy a 300mb file on a lan with 2950's from one pc to a server the file transfer takes around 13 seconds. If I implement router on a stick with a 3620 and do the same file transfer between the pc and server but ...

Hi all, I am running BGP with one of our ISP. My ISP has given his loopback address to configure as BGP neighbour at my end. While i am pinging to that neighbour IP from my router means loopback address of my ISP then i am getting "timed out...

Release Notes for the Catalyst 8540 for Cisco IOS Release 12.1(12c)EMay 28, 2002Catalyst 8540 Cisco IOS Release 12.1(12c)ERestrictionsPort Snooping RestrictionsThe snooping source port and destination port cannot be the same port.You can only snoop w...

I've 3 catalyst connected between each other via etherchannel. My issue is this catalyst are doing HSRP. Let say my root is catalyst A having preempt priority 200, catalyst B priority 190 and catalsyt C priority 180. Now i have a problem with my vlan...

Where can we find the oid valuesfor all counters in cisco routersand RAS?We want if for all the Cisco router series from 2600 to7500.

I have a 2610 with a 4E connected to a cable modem. I successfully have it connected using DHCP to acquire an IP number. I had to put a static route pointing to the default gateway that the cable compny supplies as pointing to the interface showed j...

hello, there are 2 routers connecting to one external application server through 2 leased lines, between the server and the 2 routers, there are mix of other routers also. when we set the EIGRP on the 2 routers, even with Variance 2, 60 or 128, we co...

We have a 7206(NPE-150/128MB RAM/16MB Flash) using a C7200-I/O-FE supervisor module. When the router boots, there is no support for the Ethernet interface on the supervisor. I receive the following error message during boot.GT64010: Device ID error, ...