A cat6k ethernet port is racking up large amounts of in and out discards but no error show on the port e.g crc etc. Under what condition does the port consider it should discard inbound frames that are not errored? is it buffer related?
A cat6k ethernet port is racking up large amounts of in and out discards but no error show on the port e.g crc etc. Under what condition does the port consider it should discard inbound frames that are not errored? is it buffer related?
When I use dialer profile, and config ip ospf demand-circuit, the ospf doesn't suppress the hello on this interface. The IOS support the ip ospf demand-circuit command under the dialer profile or not.
Is a dialer-group required to identify interesting traffic or will the link stay active because it is using the backup interface command?
We have a mixture of async modems and ISDN TAs dialing into our Cisco 3640, which has multiple PRI and 30 DigModem modules. We can set an "absolute-timeout" on the Line interface for the modem connections.How can we set a similar session timeout for ...
What is the maximum number of IP routes supported in a Cisco 2620 with 40MB DRAM running IP Only IOS?
I have 8MB internal flash SIMM and a 8MB PCMCIA flash card on a 3620. I need to install an IOS image greater than 8MB. Is it possible with this configuration ?
Is it possible to configure IPX-EIGRP over an IPX-WAN unnumbered WAN link?interface Serial0/1 ip unnumbered Loopback66 encapsulation ppp ipx ipxwan 0 unnumbered a-6!ipx router eigrp 1 network all!
I have a Cisco 1720 router with a WIC 1-Enet module that I need to configure so that it will accept a DHCP assigned IP address from my ISP using a DSL connection and PPOE. The ISP drops the connection every 24 hours (for security purposes) and requi...
Hi, i am having big trouble configuring a CISCO 3660 with 4 PRI´s as a dialin server using ACS V3.0 and MS-Chap-V2 with password expiration feature.Everything is fine until i set the "user will have to change password next time" switch in Win2K, when...
Hi, I am using NMS 4th Edition. We have cat 6513. When I am chacking these Cat6513, it's show's all modules fine, only for WS-X6381-IDS module, it's show's that "UNSUPPORTD CARD".The version and modules detail is as follow:CC-CORE-6513#sh verCisco I...
Just wanted to check if anyone knows the schedule for releasing NAM support for IOS?
I have three pri's connected to my 3662. All three pri's are associated with the same number by BT. At the moment when a dial is instigated each pri is used in turn. I want to know how to configure the router so that only the first two pris are used...
I have 2 mainframes with separate NETID's. Each mainframe has its own CIP. I currently send MSNF data from mainframe to mainframe using a FEP on each mainframe. I would like to get my MSNF traffic to use my CIP interfaces. I was told that I could tur...
Hi,Is there a way to control the assert-time out / prune time-out in PIM dense ?I want to reduce the 3 min wait an interface in DM stays in prune before trying to re-forward again. Practically speaking, the 3 min time-out is leading to an unacceptabl...
Everything I read about overlapping networks talks about a solution that requires the router to see DNS requests. This is not logical since the NAT router is usually a border router and will not see most, if any, DNS requests.Can it be implemented u...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |
User | Count |
---|---|
2 | |
1 | |
1 | |
1 | |
1 |