Hione of my 9300 with IOS Version 16.6.5 (CAT9K_IOSXE) just lost PoE on all 48 ports. is that an IOS Bug?Do i have to upgrade the IOS to gold version or just reboot will do??
Hione of my 9300 with IOS Version 16.6.5 (CAT9K_IOSXE) just lost PoE on all 48 ports. is that an IOS Bug?Do i have to upgrade the IOS to gold version or just reboot will do??
DHCP Pool range ip dhcp pool datanetwork 10.60.86.0 255.255.255.128default-router 10.60.86.2 Now if you run steag#Sh IP DHCP pool Data Pool Data :Utilization mark (high/low) : 100 / 0Subnet size (first/next) : 0 / 0Total addresses : 126Leased address...
Hi guys. I am trying to configure telnet on a ASR router 1001. I already run all the commands as per article but everytime that i try to telnet is stuck on the message : --Waiting for IOS Process--. I know that to telnet we need to enable login loc...
Hello!We need to refresh all our access switches for 120 remote sites. They currently have a mix of SG200 and SG300. We also have 5 bigger sites that have C2960X stacked. We talk about 10-100 users for small sites and 200-250 for the 5 bigger sites.W...
Hello for everybody.Is it possible to add secondary ip helper-address for interface vlan or subinterface (like ip address secondary).I tried with different ios vesrion with catalys 9300, isr 4k and 2g - but all unsuccesfull. OF-00-SW-03#sh run int vl...
Hi experts! Is it possible to do destination NAT on a Cisco router? I just want when my internal users try to access a server on my local subnet IP say 10.1.1.1 then I need to redirect them to a server on the cloud say 182.1.1.1. *My internal Network...
Hi folks, we have a Nexus 5k switch which does ITD for load balancing.It works well only for a VIP. The problem that we have iswe use in our Servers multi VIP assigned by simple containers inside the host and when we configure ITD for multiple VIP ho...
A couple days ago, when I used the "netsh interface ipv6 show prefixpolicies" command on my Windows 10 system, it resulted in this standard result: Precedence Label Prefix ---------- ----- -------------------------------- 50 0 ::1/...
I would like to setup VIRL on my Apple MAC computer?
I am having an issue with my RV345 where I cannot ping the router from the WAN. When I ping XXX.XXX.XXX.138 I get nothing. I even set up the firewall to allow all 'ICMP Ping Reply' and 'ICMP Ping Request' and that did not appear to work. My issue see...
Hello Dears,I have one VSS in my network and I wanted to connect them with two routers via VRRP link, but I when I finished configurations it seems that I have loop on the VSS because it starts bugging the cPU usage increase higher. Below is my confi...
where these commands came from ??how i learn them from which cisco book ??
Hi,in My current scenario i have two Cisco 5520 ASA running in Active/standby mode and a single Fortinet unit is connected to primary firewall.every thing is working smooth, and Firewall is failing over properly in case of link failures.Now we want t...
Hi, I am unable to ping the PC1 (area 0) from PC4 (totally stubby area). Please find the below packet tracer config. I have done the below configuration in the cisco packet tracer.1. Create two new VLANs (10 and 20) on Switches, set two trunk links b...
Hi All,I have one internet router with two ISPs, (Serial 0/0/0 connected to ISP-1 and Serial 0/0/1 connected to ISP-2).I configured IP SLA 10 and 20 as follows:ip sla 10 icmp-echo 8.8.8.8 source-interface serial0/0/0 frequency 6 timeout 6000ip sla sc...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:
Subject | Author | Posted |
---|---|---|
03-20-2023 08:49 AM | ||
03-20-2023 07:11 AM | ||
03-17-2023 07:38 PM | ||
03-16-2023 03:48 AM | ||
03-14-2023 01:40 AM |
User | Count |
---|---|
1 | |
1 | |
1 | |
1 |