How can udp packets can be enabled on a CMTS so that stock datas can be forwarded over a cable network, which can be used by end customers spanning a wide area with their cable modems.
How can udp packets can be enabled on a CMTS so that stock datas can be forwarded over a cable network, which can be used by end customers spanning a wide area with their cable modems.
We have nat configured on a 1700 series router with 2 public addresses given to us by our ISP. We have been running this way for 8 months. Recently we had a need for 2 additional addresses but the 2 new ones the ISP gave us are a different network nu...
With 5 Catalyst connect through Gigastack.Can I connect them alternative one with port gi 0/1 the next with port gi 0/2 , the next with port gi 0/1 and so on ?To my customer I had some problems perhaps about STP.In fact if I entered sh spanning-tree ...
Don't know which discussion forum best matches this question, but here's my question: We have an outlying building we want to tie into our main network in another building. I'm looking at the Cisco 2900 LRE series switch and CPE LRE hardware to ru...
I configure FR for 7206 connect to ATM subinterface for GSR, both PVC are up, but the line protocol is down.
I WANA KNOW IF THERE IS ANY PROBLEM WHEN CONNECTING IBM ROUTER WITH MULTIPLE CISCO ROUTER OVER FRAM RELAY
Hi,Just to confirm some details....I am setting up a WAN link to a remote office via a BT 2Mbps serial link. Both ends will be using a 1721 router with a X.21 WIC for the connection and a Fast Ethernet connection into the network at each end. I have ...
I have a customer (inexperienced network administrator) has the following stations setup and problems:Host A = 10.1.1.10 /24Host B = 10.1.1.6 /16Host C = 10.1.2.8 /16All above stations are connected to a Cisco Catalyst 2950 switch.Host A can ping to ...
What are the rules for a device to begin using the High Capacity counters in the extension table? Does anyone know if Catalyst swiches support the ifAlias variable? Are there known issues with this?
Hi everyone ! I have this problem: in a Central Site I configured a Cisco 2610 router connected with a 2 ISDN device (s/t). In a 3 remote site I have connected 3 (one for each site) cisco 801 router. My problem is that when a Cissco 801 call a Centra...
I'm curious to know if it is possible to collect bi-directional netflow records over two separate VLANs. I have a single-mode fiber line run between a Catalyst 6509 and an F5 Networks BIG-IP box. I have two VLANs set up on that link, one for inboun...
This may be beyond the scope of this board, but has anybody used the Net::Telnet::Cisco module for Linux to automate backing up a down line? Until Cisco implements a fail over for ethernet interfaces that go down without physically going down, I'm s...
Hello ,We have Cisco 3640 RAS server (IOS 12.0) on our Network for Dial in connections from home users . It has got own user database (no RADIUS & TACACS ) and we do create user accounts on 3640 itself . It has one FE port which connects to local...
Does anybody out there know if I can get a Shiva ISDN Accessport/D ISDN router to work with a Cisco 2500 Bri interface using dialer map etc. I can get the two to make calls to eachother and authnticate but thats all.
Greetings everyone,We are trying to monitor traffic at one of our sties on a 2950 and have run into a problem where the dst port goes line protocol down. There is only one switch and int fa0/24 connects to our 3640 router. Int fa0/23 is where the s...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |
User | Count |
---|---|
2 | |
2 | |
1 | |
1 | |
1 |