Have 2 routers running eBGP and using static routing internally. Instead of using default route of - ip route 0.0.0.0 0.0.0.0 hssi 2/0 - I want to static route each subnet out hssi 2/0 i.e. - ip route 208.165.197.0/24 hssi 2/0- ...
Have 2 routers running eBGP and using static routing internally. Instead of using default route of - ip route 0.0.0.0 0.0.0.0 hssi 2/0 - I want to static route each subnet out hssi 2/0 i.e. - ip route 208.165.197.0/24 hssi 2/0- ...
I want to add a secondary set of ip addresses to the router. Can someone give me a step by step. I'm going to add them to the FastEthernet0 interface.I'm using iso ver: 1.1thanksJonathan
I am trying to load Cisco MIBs for a Cat5505 into Unicenter 3.0 but it won't load. I downloaded all the MIBs for the Cat5505 but it won't take it. Any thoughts?
I'm trying to make the case for purchasing Cisco Works 2000 for my company. Is it the case that passwords on all our 200 routers could be changed at one time? (Not to mention the switches). Currently, this is a very tedious task, as you must know. So...
This may or may not be the right place to ask, but here goes anyway. As far as the Ciscos buffers are concerned, what types of information gets stored in what type of buffer. For example, I would expect a very large routing table...such as a BGP rout...
I have a 2620 connecting back to 7206. I would like configure the WAN interface of the 2620 to reserve bandwidth for a voice application. I'm a bit confused as to what command should be used ....Policy QoSclass ProLogixbandwidth 65 ??? orPriority 6...
Can anyone tell me why I cannot get from the outside pointing at the outside address ( the dialer ) port 86, to port 23 on the inside,The dialer is assigned a static address on connect. I can telnet into port 23 @ 10.10.10.2 from inside the router.--...
I have a unique issue that I ran into and I can't figure out what is happening.I have a hub router with multiple frame pvc's over a single DS-3. At the remote ends I have a mix of 1602, 1720's and 2611's. They are all pretty much configured the sam...
Hi,I am installing a 1721 Modular router with a BT Megastream 2Mbps link as my main pipe, but also a ISDT connection as my failover. I am using a WIC-1T with X.21presentation for connection to the Megastream and another WIC-1T for the ISDT. What I ne...
we use 2 version of CW2k, one running on NT the other on Solaris.Now we want to replace the NT machine with another Sun.Do we have to buy a license for this new Sun, or can we use the existing Solaris-license on a second Sun?2nd question: how can we ...
Hello Robert,Is there any difference as far as the Cat 5K and Cat4K. The Cat5K is going away? The CIOS is basically the same. Right? How long will the Cat5K's be supported?Thanks,Joe
have aquired a Cisco 1600 router that had someone try to reset the secret password. He set the config-reg to 1x2102 instead of 0x2102 and now the router boots up to a blinking cursor and nothing else. cannot enter via console or any other way as far ...
Is it possible to setup AAA with MS IAS RADIUS SERVER I want to setup our PIX 515E-DMZ-R so that internal users need to provide a username and password to access the internet. In conjunction I would like to limit where people can go based on thier us...
Does anyone know of any issues with multicasting between a nortel router and cisco router. Thanks
I just had a DS-3 installed and I'm wondering if there is a way to make sure that I can utilize the full bandwidth. Has anybody done this before? Thanks in advance.Jpoulos
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |
User | Count |
---|---|
2 | |
1 | |
1 | |
1 | |
1 |