Does anyone know of any issues with multicasting between a nortel router and cisco router. Thanks
Does anyone know of any issues with multicasting between a nortel router and cisco router. Thanks
I just had a DS-3 installed and I'm wondering if there is a way to make sure that I can utilize the full bandwidth. Has anybody done this before? Thanks in advance.Jpoulos
hello everyonei need a tools / software to benchmark an old switch system in my costumer's site before he decided to buy the new catalyst 3500.they are still using 5 year old IBM 8271 10/100 switch. and sometimes the switch hang out. BUT he still wan...
Is there any simple SNMP tool for monitoring FR PVC's on IGX 8410 other than StrataView? .Pls help in finding a sloution for this . Also tell me if there any RFC's for implementing these MIB's for monitoring the FR PVC's.
3 Servers are connected to a Cat 6509 with Intel and Compaq Gigabit NICs - they have poor performance (80kb/sec) and are loosing 10 percent of the pings - there is no traffic on the LAN.The Cat 6509 was completely replaced - the problem ist the same....
One question. A laptop user is using an automatically assigned IP adddress by using a DHCP server. If this laptop is properly shut-down and then he/she has to go to work in another office that has a different subnet, does this user have to mannually ...
I have CW2K running on Solaris 7. Several months ago, the IP addresses of a number of network devices were changed. The devices were deleted and re-added to the CW databases. Today, it was discovered that the CW server is ARPing out to the old IP ...
Does Cisco have a pure IP DSLAM...ie no ATM needed for the WAN link? I know the 6260 supports IP+ATM but I have a Gig-E MAN and do not want to inccurr the complexity of overlaying an ATM infrastructure just to support my DSLAMs.Thanks,Patrick Greene
We recently bought a 2621 router with 3 Ethernet interfaces. We also got a DirecPC satellite dish to serve as a redundant Internet connection for both our LAN and web servers (no ISDN, DSL, or cable is currently available here out in the sticks, so ...
Hello,are there any patches available for integrating 2950 Catalyst into RME 3.2 ?Thanks for your helpThomas
Is there a way to monitor/conigure switch clusters using CiscoWorks when they are set up with just 1 IP address? I have set up CiscoWorks 2000 LAN Management Solution and everything works just fine up to the access-layer but user tracking and other ...
Hi, I am fairly new to CISCO environment. I am trying to upgrade two switch 10 Base-TX(WS-X5012A) modules in a 3 yrs old catalyst 5000(Supervisor engine II) to a 100 Base-TX module (WS-x5224). I found the CatOS version requirement for the ...
What would be the best method to test latency through an ATM network with DSL? Specifically, the core is an LS1010 with 6130 and 6160 DSLAMS at remote offices. We use the 4-port FLEXI (w/ NI-1 and NI-2) and 8-port DMT (NI-2 only). The boxes connected...
QuestionHow many L1 OSI areas would you expect to support on the following platforms?Within each L1 area the number of Network elements is expected to be around 10-15.The Cisco docs say that you can configure a maximum of 29 level 1 areas. 2621364036...
I'm interested in being able to get SNMP values like : RouterA#sh ip eig nei detail IP-EIGRP neighbors for process 827H Address Interface Hold Uptime SRTT RTO Q Seq Type (sec) (...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |
User | Count |
---|---|
2 | |
2 | |
1 | |
1 | |
1 |