Does medianet work on nexus? Whats the roadmap.
Does medianet work on nexus? Whats the roadmap.
When i check the Router CRS-1 log, these log seem to be that the upper fan has problem!even the CRS-1 has no alarm on RP, the fan led status is blue as normal.---------------------------------------------RP/0/RP1/CPU0:dng-co-crs-01#co-crs-01#RP/0/RP...
Hi,My mechanical engineer needs detailed measurements for the hole patterns on the sides of the Cisco 2911.Any ideas where I could find this for him?I've searched and read the installation docs, which shows pictures of the units. Although helpful, th...
I used to be able to set an uplink port with the interface command "port network" so that it would not learn all the mac addresses that are being flooded down to the switch. It does not seem to be there on the 2950's or 35XX switches.Where did it go...
Hi,I have a Airnet 1240AG and have our main SSID set up on Radio0-802.11G. It uses WPA TKIP. Everything works fine on it. Recently we have been getting a lot of visitors who need wireless access, so reather than hand out our main key to visitors, I d...
Thanks for the perf mon links. So does perf mon work with EMM or is it with NMS?
Can anyone confirm to me the order the 8 cables go into the octal plug.The cable is a X.21.DTE 8 LEAD OCTAL part No 72-1100-01. The cables are not in numerical order (as in 0 to 7 as per the serial ports). I'm trying to trace cables and don't have a ...
Hi All, I'm trying to figure out how I can do QoS on a 6500 and police traffic based on an IP access-list. I want to define an access-list which specifies the traffic based on soure and destination IP addresses. I then plan to use a class map to matc...
Hi,I came across medianet solution and am looking for more information on its capabilites. Also whats the difference between media monitoring and performance monitoring?Thx
Not quite sure what will be best practise for me here:3 x SG300-281 x SG300-10MPPlaced in 3 locations1:1 x SG300-282:2 x SG300-283:1 x SG300-10MPI have 4 lines between locations 1 and 2, and 2 lines between locations 2 and 3My idear was to use the 4 ...
customer replaced a chassis of gsr, and forgot ospf md5 key. he use encrypt password from config to config ospf neighbor. he found some neighbor is up.but some ospf neighbor can't get up.what affect ospf MD5 comute result! thank you!Tom
Do the Cisco CGS 2520 and CGR 2010 support power over ethernet?
Dear Cisco Community,We have got a Cisco 2921/K1 router. Behind the router we have got two openvpn server, which are serving now 120 openvpn clients with heavy traffic.We are using 1 giganet port for external ip, and 1 port giga for internal for open...
Hi Geniuses,I have a requirement to track reachability of an interface with ip sla. i used the following configuration:I'm going to use this to put a reliable static route.I want to remove the route after 3 pings failed to the destination IP 10.1.1.1...
I have the following configurations for switch to switch connectivety. sh int sh config int2960 will not take full duplex setting. Thanks,Core switchWS-C4506 cat4000-i9s-mz.122-25.EWA10.binFastEthernet5/8 is up, line protocol is up (connected)...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 01-22-2025 07:00 AM | ||
| 11-14-2024 09:33 AM | ||
| 10-24-2024 11:51 PM | ||
| 10-20-2024 10:52 PM | ||
| 09-26-2024 02:28 AM |