does the 3512/3524/3548 support cut-through switching or store-n-forward.we need cut-through switching for a project we areworking on.
does the 3512/3524/3548 support cut-through switching or store-n-forward.we need cut-through switching for a project we areworking on.
Can somebody indicate me an document which explain about boot recovery of image IOS to Catalyst 8540?PS for example if it is in rommon>.ThanksLorenzo
Hi all,My customer wants load balancing solution to a branch office. He heard that it can be done with static routes, but as I know load balancing can't bedone by deploying static routes. Any info about this? Can it be done or how effective will it b...
hello all,I have an architecture problem. Here is my networkarchitecture: /---------------Router B---------------\Router A LAN \---------------Router C---------------/On the LAN side, HSRP is configured (Router C isactive). OSPF is used as routin...
On a cisco 3640 Router, I''m currently running IOS 12.0(7) and all is well. I tried upgrading to 12.2 to take advantage of snmp support for vlan sub-interfaces on a FastEthernet port. After restarting the router, all interfaces come up except the ser...
I have a 3640 connecting to a 1601 via a 256k kilostream link. From the 3640 I can ping all the interfaces on the 1601 and the Internal LAN, but when I try to ping the 3640 LAN from the 1601 I get the reply from the WAN address on the 3640 saying the...
We hv 2mb LL (fiber) from our ISP..Can we assign 128K to one Network segment and remaining b/w to the other network . ( Routers E0 and E1 is diff network ( cisco 2621 ))
need some help, i need to access my corp office from a remote location, the remote location has a dsl line with a static ip, i need to access my unix box which router will work best, im thinking the 806 many thanks in advance
Hi, I want to configure an ether channel in 3524 with 6509. There are 2 3524 configured in cluster mode. 3524 has two gigabit ports. So I am left with one port from each switch to configure channel(the other port is used for clustering). But when...
I hope you can help. I would like to know the commands to check the traffic running through the 3500. We are having problems with an application and want to see if the 3500 is catching it. What would be the command line t enter. Thanks in advance.
I have two 2600 routers, each with TWO WIC-1DSU-T1 modules and a Fast Ethernet card. I am trying to set up two parallel p2p T1s over these two routers. Other than the configurations described earlier, how do I do load balancing, and to set it up such...
I do have a case scenario where the private network is running OSPF and IGRP (135.50.x.y network). The core is running OSPF and we are doing mutual redistribution between the IGRP and OSPF domain. When I redistribute a default route from my OSPF netw...
I just intalled a new WAN link to our production facility.. At Site-A, I have a Firewall connected to the net and internal interface of 192.168.1.1 . I have the WAN router Eth0 192.168.1.2 . The Site-A WAN router is connected to the Site-B WAN route...
we have a number of catalyst 6509s running IOS 12.1.8a[e3] that are logging the following error:%IPC-SP-5-LIMIT: 682 messages pending for the port 8.10000Hardware is sup1a/msfc2/6408/6416/6248/6224Other switches with similar config appear OK.Any help...
I have a 2948G L3 and I need a DHCP server for each VLAN, can the Switch be a DHCP server per port??
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |
User | Count |
---|---|
2 | |
2 | |
1 | |
1 | |
1 |