Can anyone point me to info on these parameters when configure Frame-Relay Traffic Shaping? Are these values derived from my AR and CIR or is there some calclulation that I mus perform.Any help appreciated.
Can anyone point me to info on these parameters when configure Frame-Relay Traffic Shaping? Are these values derived from my AR and CIR or is there some calclulation that I mus perform.Any help appreciated.
I have problem w/ switch 2900xl, one of the port not work and light indicator it show red color, here the information I get from SNMP :--FastEthernet0/15 is administratively down, line protocol is down Hardware is Fast Ethernet, address is 0002.7d3...
I added and access-list to one of our 7206s to stop HTTP traffic to a specific location. Unfortunately, it also blocked required TN3270 traffic too. Any information would be greatly appreciated. Here are the lines entered:access-list 104 deny tcp ...
I have a big problem with 2924XL-EN. Many of them show Experiencing Error on ports (like this: %LINK-4-ERROR: FastEthernet0/1 is experiencing errors). I found that before that port will be experiencing errors, it can use normally until it shows "up-d...
I recently bought gigabit ethernet cards that are 64 bit. One of my engineers say that the motherboards in our servers are 32bit and so the card won't be able to negotiate faster than 100. Is this true? is there any reason to upgrade the cards? Thank...
Is there something special to do if i instala 1600 router with BRI S/T on a S0 bus.It works on a TNR (T0)but not on a S0 bus.Thanks
I use the traffic rate command in the frame relay calss maps to control traffic.in the example below the access at the site is 1024kand the CIR 640Kmap-class frame-relay Jam frame-relay traffic-rate 640000 1024000 no frame-relay adaptive-shaping fram...
Wats the maximum link speed x.25 can support
I have a Catalyst 6509 with an MSFC, behind a PIX firewall connected to the internet. One of the interfaces on the MSFC (Vlan 10) has two ip addresses (networks) one being a secondary, both being NATed. When I put this configuration on line I can g...
just learning about cisco routers and adding them into my network, someone mentioned to me that I out to see if there was a software "brouter" that I could add to my existing router. I am not sure what this is or what it does, looking for any inform...
I have a router 3640 and i need a capacity grater than 8 Mbps, i have this router with 2 modules NM-2W with 2 WIC-2T, so I have 8 serial interfaces.Can i have 8 Mbps in one of this module?Why if i connect this 4 serial interface i can pass 7 Mbps o t...
Can someone please give me some hints on ip route optimisation accross wan linksthanks in advance
I would like to know if a switch port of a Catalyst 6506 can belong to 2 or more vlan at the same time whitout be a trunk port.Thanks
I have a primary link to one router with a set of static NAT translations and I have a backup link to another with the same translations. If I take down the primary links, routing directs traffic through to the backup link but I seem to lose the stat...
After requesting and talking about "Class A" tests a bazillion times, I thought it might nice to know - specifically - what it is. Can anyone technically define what the test is, how it's run, what it looks for, and/or clarify what the results will l...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |
User | Count |
---|---|
2 | |
1 | |
1 | |
1 | |
1 |