I need to Know the Catalyst 2948G-L3 support the Module WS-3500XL for Stack with others Switch Catalyst 2924M-XL and Catalyst 3548.Thanks,Franklin Briones
I need to Know the Catalyst 2948G-L3 support the Module WS-3500XL for Stack with others Switch Catalyst 2924M-XL and Catalyst 3548.Thanks,Franklin Briones
Just a quick question....Is there a maximum number of entries that can be held in the ARP table of an MSFC in a 6509?The MSFC routes 7 VLANs and there are approx. 1000+ devices on the network.
when design the ospf network, can we use the same pool of networks which is ubnetted using 30 bit subnet
Hardware: Cisco 2620 Router Scenario: I want to setup a block of 14 ip addresses so they can only access one certain website or ip address and they can not go anywhere else. I have been using a 255.255.255.240 mask. Here are a couple of statments tha...
HiI have 2 leased lines connected to different internet providers on my 2610. I want the router to loadbalance between those two according to the load/delay/(line quality :response packets of the line or request packets lossed) , to have one high qua...
hi,I am trying to tftp the startup-config file from a Cisco 2600 Router over the internet [i.e from it's outside interface - the access-lists allow port 69 from and to any address 12.1(7). When I try to execute copy startup-config tftp in priv exec ...
Hi allI am wondering if someone can help me with the following situation or if there is any documentation on it somewhere.We have 2 buildings connected through a T1 line. In building 1 we are running Windows NT 4.0 Terminal Server running DHCP. In ...
I have a module on 7206 VXR, PA-4E1G/75,but i do not know what cable i should select for this module ?any helps? thank you
Are ATM PVC's considered secure or should some type of encryption be enabled on the edge devices.
I've just converted all of our WAN from 3Com gear to Cisco. The hub is a 3661 with multiple T-1s coming in and the far end sites are 1720s, mainly T-1s but a couple 56Ks also.On the 3Com gear I could enable compression (software)on a per-packet basi...
This may sound dumb but... I have a Cisco 2600 and need to do some filtering of ports and IP addresses. Not really sure what the command is to do this. I can telnet to the router and have all the right passwords but need to know how to set this.An...
Is it possible to put tresholds on catalyst utp ports so an alert will be sent when it generates a certain amount of errors in a period of time. Can Cisco works 2000 play a role in this or is there third party software which can do this tasks.
Can somebody tell me what encapsulation is used in a PAMA VSAT connection. Is it PPP or HDLC or other
I would like to connect a 3640 and 1720 together, I want to simulate the t1 connection. On routers with a v35 connection i know its possible to use a dce cable on one end and a dte cable on the other end. I saw someone mention a rollover cable or c...
I recieved an error in CiscoWorks with a "HIGH" severity. The error said:"Trunk port 16/1 belonging to device xxxxxxxx has spanning-tree portfast enabled"I know this is not a good thing, however, I do not have a port 16/1. The device is a 6509.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:
Subject | Author | Posted |
---|---|---|
02-20-2024 07:45 AM | ||
02-15-2024 09:08 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM |