I recieved an error in CiscoWorks with a "HIGH" severity. The error said:"Trunk port 16/1 belonging to device xxxxxxxx has spanning-tree portfast enabled"I know this is not a good thing, however, I do not have a port 16/1. The device is a 6509.
I recieved an error in CiscoWorks with a "HIGH" severity. The error said:"Trunk port 16/1 belonging to device xxxxxxxx has spanning-tree portfast enabled"I know this is not a good thing, however, I do not have a port 16/1. The device is a 6509.
Hii have 1 cisco 1603 and 1 cisco 2621..they both have eth,serial and bri interfacesthe routers are connected with a leased line and i need to configure backup isdnthe 1603 will use one line to connect to the 2621 and the 2621 uses 1 of his channels...
Could a 6500 switch or 7500 router using 2 DS3's WAN ports, multiplex 2 DS3's lines to provide almost wire speed 100MB ethernet bridging?
I have been in many discussions about setting my switch port speed and duplex to auto or fixed. My take is that the rule of thumb is for workstations or PC's Is to set it for auto. Servers should always be set to fixed. I understand that this is the ...
How can I route these vlans so they can talk to each other. I'm doing this on a 6509 switch with a RSFC.I've set up vlan interfaces with IPs on the layer 3 side of the switch but cannot ping from one vlan to the other.Vlan 200 IP-10.2.253.253/24Vlan ...
Here is my question. I have a cataylsy 5000 connected to 2 3620 routers configured as bridges performing no routing functions. These 2 bridges are connected accross fractional DS3's to 2 other 3620 routers configured as bridges. These bridges ar...
All the documentation on this subject talks about Cisco talking to Cisco but what if you have a situation where you have 3Com routers on the other end. Is there any documentation on this subject. My problem is that we are migrating all routing and sw...
I have installed Virtual Computer Networking at one of the office sites and am trying to connect to our other site with it that has a Cisco 800 serious router installed. Everytime I try to conect I get connection failed could someone please tell me ...
Hi,Is it possible to limit the Bandwith using Catalyst 2912XL and Catalyst 1912XL (VLAN configured) ??The Catalyst 2912XL is connected to Cisco 3640 (also VLAN configured)Thank you for the help.Henry
We want to use information collected by Cisco Works to enrich the functions of our own NMS. Does Works provide any API or developing tools? And where can I find more information about integration utility?
can i control cumalitive bandwidth of say 4 ports to 1 mb in 6500 which is in a pvlan community using qos.I am sucessful in controlling individual bandwidth but unsucessful in cumalitive bandwidth controlregardsshaji
In an effort to find a quick warm & fuzzy....can anyone please advise if there are additional configuration requirements when using secondary addresses? I'm setting up two class c's on a single internal ethernet intfc. All servers are on class c ne...
I am looking for the power supply specifications for this old 765m router, output voltage ac/dc and current rating , pin outs would also be useful.Thanks in advance
I am trying to convert from a fractional T-1 to SDSl. Also I would like to keep my exisiting class C address. The DSL provider only give 4 public addresses and I have a full registered class C. This would effect web servers, mail, and data replicatio...
Hello,I want to enable UDP packets, which consist of trading datas genarating from one server in a different network and allow this data to reach enduser at their home.We are having an existing setup of Cable ISP with uBR 7223.I was trying to route t...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
02-20-2024 07:45 AM | ||
02-15-2024 09:08 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM |