I was wondering if the multicast commands are done on each individual serial interface or just on the MLPPP interface, or both?Thanks, Karen
I was wondering if the multicast commands are done on each individual serial interface or just on the MLPPP interface, or both?Thanks, Karen
Hello,Requirement: connecting 2 lan switches with SFP cable.The LAN Switches to be connected are: C3560-24TS+2SFP with C3750-24TS+2SFPCable SFP: CAB-SFP-50CM-cablewhen the installation is done, the error show up in the SFP interface, as below:Port ...
We keep getting passed on to VARs for advice on how to grow our network using Cisco equipment. Is there someone i Cisco who we can talk to in confidence? Looking for a techie person...TIA.
Hello Netpros,Here i am looking for advice related to transmission. I am basically from IP team and recently our transmission team has installed a STM-1 connectivity on MUXs between two ends.Problem Summary:- we are doing end to end testing to check...
I have a 2800 series with a 64MB flash memory. Everytime it relaods or reboots the startup config is not populated into the running config. can someone help be fix this. thanks
Hello,I'm looking for a way to update and configure an Cisco ASA without serial connection.I can only use an network connection.I was wondering what my options would be.Kind regards,Jean-Luc
Hi,I need a Cisco router with two Ethernet ports which supports IPSEC, QoS, NATing etc. There is only 20-30 users going via this router. Which router is recommended and the IOS version?I thought 1721 is good, but I need to download a IOS which suppor...
Hello,Just purchased an Aironet Wireless Access Point Prod. #: AIR-LAP1242AG-A-K9 with Cisco IOS 12.3(4)JAIn the instruction it says plug in a DHCP server and access the Web interface. I did that I got an IP I am preaty sure because I looked in the l...
Hi all, Can anyone tell me why my new switches arent showing up the switch health information on them from http, I can see a fan spinning around and the temp, but the bandwidth used etc isnt showing anything
I have a Cisco 881 router configure with 3 VLANs on three different fastethernet ports. Each vlan has a separate network address vlan2 = 192.168.10.0, vlan3 = 11.0, vlan4 = 12.0My goal is to keep the VLANs separate from each other.( Example as: vlan2...
Hi someone,I login to Cisco1812 using telnet and enter "show tcp" command then mss value displayed below."Datagrams (max data segment is 1260 bytes):"The IOS version is 12.4(15)T9.My Router was only configured the ip address and line vty, minimum con...
I need to calculate bandwitdh to figure out what kind of connection i need. I know if i take ONE single computer with wireshark loaded then run the programs then stop the capture.....How long do i need to capture it for? 1 minute, or 10 minutes, or ?...
Hello,I'm diving into switching details and saw the following:# show controllers cpu-interfaceASIC Rxbiterr Rxunder Fwdctfix Txbuflos Rxbufloc Rxbufdrain-------------------------------------------------------------------------ASIC0 ...
Hi All,Can we terminate an internet link with ethernet handoff on a firewall.If yes what are the pros and cons of it.how the routing will be done in this case.please assit with above queries.thanks
I've seen this happen on 2 different 'pairs' of 2950s, so it's time to investigate. The scenareo:simple trunk (no vlan definitions) between 2 2950s. 1 switch looses power, when power is restored, the switch that didn't lose power doesn't pass any tra...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 03-24-2025 06:42 AM | ||
| 02-26-2025 06:41 PM | ||
| 01-22-2025 07:00 AM | ||
| 01-22-2025 05:28 AM | ||
| 12-30-2024 06:12 PM |