Please provide the updated version of the document "Cisco Connected Factory—PROFINET Wireless Design and Implementation Guide". If the updated version is unavailable, provide the following data:- equivalent of Cisco 5508 WLC- possibility to use the...
Forum Posts
Resolved! Virtual tunnel interface status down
Hi, Status is up protocol is down not sure what is wrong in the config any guidance here? ASR920 SW version is Cisco IOS XE Software, Version 16.06.01 Interface IP-Address OK? Method Status ProtocolGigabitEthernet0/0/1 192.168.30.18 YES NVRAM ...
Hello,i am trying to Upload the image from an FTP server to a cisco catalyst C3850 and i am having the below error message% Connection timed out; remote host not responding%Error opening scp://*****@****/cat3k_caa-universalk9.16.12.05b.SPA.bin (Unde...
Hello guys, Situaion: Customer A - own smart accountCustomer B - own smart account Customer B has CSSM with own licences but need use particullar licences from Cust A on own CSSM(from SP) Is possible do it between Smart accounts ? Via Virtual Acco...
Resolved! Can I have an extended LAN over WAN?
Hello Community! I was wondering if I can have layer 2 traffic over a layer 3. Let me elaborate. I have a site A that has two servers working as a cluster. My client wants to replicate this cluster into another site that they have. The problem is ...
Hello,my 2620 hangs at the initial setup:-------------------------Cisco Internetwork Operating System SoftwareIOS (tm) C2600 Software (C2600-I-M), Version 12.0(7)XK1, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)TAC:Home:SW:IOS:Specials for infoCopyright (...
Resolved! Failing with simplest NAT config ever
I am using a Cisco 1921 with Gig0/0 and Gig0/1 interfaces on it. I'm trying to do something really simple, however it isn't working at all and I feel I must be overlooking something very basic. ip cefno ip source-routeip classless!interface GigabitE...
Resolved! Remote internet access
Hello Community I need to have internet access on my remote sites to monitor the power supply (a cloud based solution only),the remote site are in a rural city with no internet connexionthe idea is to have a remote internet access from the hub Router...
Hello, i have got two Cisco routers connect with HSRP configuration. On one interface of these routers i need change group ID due to change virtual MAC address. What is the best practise for this change ? I want to avoid outage on other interfaces.N...
Dears All I installed a new Fan tray( ASR-9006-FAN )to my box beside the first one ASR-9006-FAN -v2 for ASR9006 and i need to know what is the deference between the two versions and is that effect the service? 0/FT0/SP ASR-9006-FAN READY0/FT1/SP ASR...
Resolved! Ctrl-Shift-6-X combination for telnet
I can not use Ctrl-Shift-6-X key combination for suspending telnet connections. I'm telnetting to router A then telnetting to router B through A. In this case Ctrl-Shift-6-X key combination should suspend the second telnet session. But it's not worki...
Hi, somebody knows any email of Cisco Networking Academy support. it is very sad that is almost impossible any communication with them. Thanks
I am unable to gain access to the 1841 at the moment because I had disabled the password recovery feature. Break command doesn't seem to work. I followed this password recovery link without any luck. (C1841-ADVIPSERVICESK9-M), Version 15.1(3)T4, S...
Hi, We are migrating our network from the typical MPLS to a flat L2 network. Today, we have /30 subnets for each location and BGP across the enterprise, and our layout is hub and spoke with two hub datacenters. Due to new requirements, we have to se...
Hi, I am trying to configure an extended named ACL for this Router in packet-trace for an assignment and nothing I do seems to work. I am trying to get just one network to have access to FTP. The current commands I have are: ip access-list extended W...
Recognize Your Peers
.jpg "VIP Community Legend"){kind=icon}
.jpg "Hall of Fame Master"){kind=icon}
