10-17-2003 01:42 AM - edited 03-02-2019 11:04 AM
I've router 1601:
Cisco1601#sh ver
Cisco Internetwork Operating System Software
IOS (tm) 1600 Software (C1600-K8OSY-L), Version 12.2(10), RELEASE SOFTWARE (fc2)
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Mon 06-May-02 22:59 by pwade
Image text-base: 0x08056080, data-base: 0x02005000
ROM: System Bootstrap, Version 11.1(10)AA, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
ROM: 1600 Software (C1600-BOOT-R), Version 11.1(10)AA, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
Cisco1601 uptime is 18 hours, 56 minutes
System returned to ROM by reload at 17:33:50 GTB Thu Oct 16 2003
System restarted at 17:41:10 GTB Thu Oct 16 2003
System image file is "flash:c1600-k8osy-l.122-10.bin"
cisco 1601 (68360) processor (revision C) with 13824K/4608K bytes of memory.
Processor board ID 05330490, with hardware revision 00000000
Bridging software.
X.25 software, Version 3.0.0.
1 Ethernet/IEEE 802.3 interface(s)
2 Serial(sync/async) network interface(s)
System/IO memory with parity disabled
2048K bytes of DRAM onboard 16384K bytes of DRAM on SIMM
System running from FLASH
7K bytes of non-volatile configuration memory.
16384K bytes of processor board PCMCIA flash (Read ONLY)
Configuration register is 0x2102
------------------------------------
I tryed to boot system from tftp sever and added next-
boot system tftp c1600-k8osy-l.122-13.T9.bin A.B.C.D
---------------
After reboot i saw next-
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
[OK - 14116932/17610446 bytes]
program load complete, entry point: 0x2005000, size: 0xd76824
......................
SYSTEM INIT: INSUFFICIENT MEMORY TO BOOT THE IMAGE!
%Software-forced reload
Unexpected exception to CPU vector 34, PC = 21583EE
-Traceback= 21583EE 213C108 213C936 215E298 214B8D6 214BAEE 24367D0 2426126 200D
7DE 200D8CE 20FD070 20B1394 20C91BA 20C92C4 20C9388 21695F6 21657DC
......
Pool: Processor Free: 0 Cause: Not enough free memory
Alternate Pool: I/O Free: 1528 Cause: Not enough free memory
-Process= "Init", ipl= 4, pid= 3
-Traceback= 213C094 213C936 215E298 214B8D6 214BAEE 24367D0 2426126 200D7DE 200D
8CE 20FD070 20B1394 20C91BA 20C92C4 20C9388 21695F6 21657DC
-----------------------------
I saw message "Not enough free memory" but my image size < RAM's size.
======================================
I found that -
Router boots in boot mode, with the following message on the console:
SYSTEM INIT: INSUFFICIENT MEMORY TO
BOOT THE IMAGE!
This message only occurs when loading images that run from RAM (for example, c1600-y-mz.120-20). Since Cisco1601-1604 routers support images that run in RAM and images that run directly from Flash (for example, relocatable images), there are two solutions for the problem:
-Upgrade the Dynamic RAM (DRAM
-Load a relocatable image (such as c1600-y-l.120-20). On Cisco1605 routers, the only option is to upgrade the DRAM.
==========================================
I used relocatable image. And is't possible to resolve it without upgrade DRAM?
10-17-2003 06:46 AM
Hello,
if you load the relocatable image in flash and then configure the system to boot from flash it should work, without upgrading the DRAM.
Regards,
GP
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: