cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1315
Views
0
Helpful
4
Replies

Need Help on IP Sla configuration

ericeshun
Level 1
Level 1

I am configuring IP Sla on a Cisco 1700 series router with the commands below but I'm not able to add the Track keyword to the static route command-line   

rtr 6

type echo protocol ipIcmpEcho 172.27.0.254 source-ipaddr 172.27.0.6

timeout 3000

frequency 900

exit

!

rtr schedule 6 life forever start-time now

!

track 6 rtr 6 reachability

exit

!

ip route 0.0.0.0 0.0.0.0 172.27.0.254 ????????(not able to add track 6)

1 Accepted Solution

Accepted Solutions

Hi,

take a look here and you'll see the first IOS image where this feature was introduced ( 12.3 and further) and that it is not supported on IPBase on 1700 routers.

http://www.cisco.com/en/US/docs/ios/12_3/12_3x/12_3xe/feature/guide/dbackupx.html

Regards.

Alain

Don't forget to rate helpful posts.

Don't forget to rate helpful posts.

View solution in original post

4 Replies 4

cadet alain
VIP Alumni
VIP Alumni

Hi,

could you post show version output .

Regards.

Alain.

Don't forget to rate helpful posts.

Don't forget to rate helpful posts.

Thanks. Below is the ouput of sh version.

Cisco Internetwork Operating System Software
IOS (tm) C1700 Software (C1700-SV8Y-M), Version 12.2(11)T8,  RELEASE SOFTWARE (f
c1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Sat 29-Mar-03 15:45 by hqluong
Image text-base: 0x80008124, data-base: 0x811377D8

ROM: System Bootstrap, Version 12.2(1r)XE1, RELEASE SOFTWARE (fc1)

OBU uptime is 1 day, 2 hours, 54 minutes
System returned to ROM by power-on
System image file is "flash:c1700-sv8y-mz.122-11.T8.bin"

cisco 1751 (MPC860P) processor (revision 0x300) with 52429K/13107K bytes of memo
ry.
Processor board ID FOC07260PEX (4052560654), with hardware revision 0000
MPC860P processor: part number 5, mask 2
Bridging software.
X.25 software, Version 3.0.0.
1 Ethernet/IEEE 802.3 interface(s)
1 FastEthernet/IEEE 802.3 interface(s)
2 Serial(sync/async) network interface(s)
2 Voice FXS interface(s)
32K bytes of non-volatile configuration memory.
32768K bytes of processor board System flash (Read/Write)

Hi,

take a look here and you'll see the first IOS image where this feature was introduced ( 12.3 and further) and that it is not supported on IPBase on 1700 routers.

http://www.cisco.com/en/US/docs/ios/12_3/12_3x/12_3xe/feature/guide/dbackupx.html

Regards.

Alain

Don't forget to rate helpful posts.

Don't forget to rate helpful posts.

Thanks Alain.

Sorry I did not get back to this site in time. I was working on upgrading the IOS; however I have been having

memory challenges so I decided to come back here.

Unfortunately there is no solution.

Thanks for your response.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: