Re: why have this command.it is copy run strat:

wsline · ‎12-08-2003

In my router .why have this commad??it is copy run strat.

Router#copy run strat

Destination filename [strat]?

Erase flash: before copying? [confirm]

Imprudence to enter .my flash is erased.. Now ,I want to pour the IOS again. But the system clew that the memory is not enough to download image¡I don¡¯t kown why..

rommon 1 > xmodem ?

Do not start the sending program yet...

getdevnum warning: device "flash" has size of zero

open: read error...requested 0x4 bytes, got 0x0

trouble reading device magic number

dir: cannot open device "flash:"

WARNING: All existing data in bootflash will be lost!

Invoke this application only for disaster recovery.

Do you wish to continue? y/n [n]: y

ERR: Not enough memory to download image

router#show flash

System flash directory:

No files in System flash

[0 bytes used, 16777216 available, 16777216 total16384K bytes of processor board System flash (Read/Write)

router#show version

Cisco Internetwork Operating System Software

IOS (tm) C2600 Software (C2600-I-M), Version 12.2(15)T9, RELEASE SOFTWARE (fc2)

TAC Support: http://www.cisco.com/tac

Compiled Sat 01-Nov-03 04:42 by ccai

Image text-base: 0x80008098, data-base: 0x80C294DC

ROM: System Bootstrap, Version 12.2(7r) [cmong 7r], RELEASE SOFTWARE (fc1)

router uptime is 7 hours, 46 minutes

System returned to ROM by power-on

Running default software

cisco 2621XM (MPC860P) processor (revision 0x100) with 27648K/5120K bytes of mem

ory.

Processor board ID JMX0636112S (3333293542)

M860 processor: part number 0, mask 49

Bridging software.

X.25 software, Version 3.0.0.

2 FastEthernet/IEEE 802.3 interface(s)

32K bytes of non-volatile configuration memory.

16384K bytes of processor board System flash (Read/Write)

Configuration register is 0x3922

But I pour the ios,the system is running in gear¡¡.why ?????

kkalaycioglu · ‎12-08-2003

I don't think there's such a command. When yu issue "copy run strat" you're trying to copy running-confing to a file named "strat". May it be "copy run start" (to copy running-config to startup-config).

wsline · ‎12-09-2003

I kown that it have the command "copy run start"in router,this is in gear.But the command "copy run strat" also is in gear,so i don't understand.please tell me why..thank you !

Now,i can't pour the new's IOS,when i pour the IOS,the system clew that the storage'space is not enough,But i inport the command "show flash" in router,show out :

ks_pouchen#show flash

System flash directory:

No files in System flash

[0 bytes used, 16777216 available, 16777216 total]

16384K bytes of processor board System flash (Read/Write)

Why this.....i don't understand..

kkalaycioglu · ‎12-09-2003

Can you send output starting with command "copy tftp:..... flash:....."

The IOS image you're trying to copy may be larger than the flash can handle.

wsline · ‎12-11-2003

I understand your means.But the flash's range is 16M in my router, the new ios's range is 6.4M.

kkalaycioglu · ‎12-11-2003

Have you tried to squeeze flash ? (squeeze flash:).

wsline · ‎12-12-2003

No,no ...i don't want to squeeze flash ,i only want to pour the new's flash,but working ,the system have some question.my flash's space is enough,but the system clew the space is not enough..

router#show flash

System flash directory:

No files in System flash

[0 bytes used, 16777216 available, 16777216 total]

16384K bytes of processor board System flash (Read/Write)

why? i don't know the means.

nihal.akbulut · ‎12-12-2003

Hi,

try complete xmodem command on rommon. Because you wrote "xmodem ?", router gets ? as filename. for help on xmodem command try "xmodem -?" you can look at link below..

xmodem -c

http://www.cisco.com/en/US/products/hw/routers/ps259/products_tech_note09186a008015bfac.shtml#download_2620

wsline · ‎12-16-2003

Thank's your answer my question..Now i also find a new question,it is a new's command that "copy run (*.*),it means that the * may be any letter. as for as you input copy run any letter .you can receve the same result.please see ..

ks_pouchen#copy run a

Destination filename [a]?

Erase flash: before copying? [confirm]

please answer me ..thank you ....

wsline.