6500 QoS

[dinesh2001]

Hi All,

I'm trying to figure out how I can do QoS on a 6500 and police traffic based on an IP access-list.

I want to define an access-list which specifies the traffic based on soure and destination IP addresses. I then plan to use a class map to match this access list and police the traffic in a qos policy. I was planning on applying the qos policy on a gig interface.

As the 6500 has a different architecture, compared to a normal router, can some suggest how I can do this. I'd like to do this on a:

WS-C6509-E (R7000) with a Supervisor Engine 720

Regards

D

[lgijssel]

Class maps and ACL can be used, that's just common qos config which is not different for the 6500.SUP720.

I have tested this recently for s72033-ipservicesk9_wan-mz.122-33.

You will find that only policing is supported, at least for egress. We did not need ingress so I did not check.

Hierarchical policies are also not supported.

The other restriction is regarding the interface; it must be operating in Layer3 mode so a gig interface will only work when it is configured as "no switchport", the other option is an SVI or vlan interface.

regards,

Leo

[dinesh2001]

Hi Leo,

Thanks for your reply. I am using policy on a gig interface so it should work as I am only policing. However, I'm doing this in a hiearchical qos policy. The commands were taken without problems. Can you tell if it is actually working from the following output:

Device:# sh policy-map interface
GigabitEthernet4/3

  Service-policy output: WAN_QOS

    class-map: CLASS_TRAFFIC (match-all)
      Match: access-group name TRAFFIC-ACL
      police :
        2000000 bps 62000 limit 62000 extended limit
      Earl in slot 1 :
        218 bytes
        30 second offered rate 0 bps
        aggregate-forwarded 218 bytes action: transmit
        exceeded 0 bytes action: drop
        aggregate-forward 0 bps exceed 0 bps
      Earl in slot 2 :
        0 bytes
        30 second offered rate 0 bps
        aggregate-forwarded 0 bytes action: transmit
        exceeded 0 bytes action: drop
        aggregate-forward 0 bps exceed 0 bps
      Earl in slot 5 :
        510781585 bytes
        30 second offered rate 84424 bps
        aggregate-forwarded 510702495 bytes action: transmit
        exceeded 79090 bytes action: drop
        aggregate-forward 140008 bps exceed 0 bps

    Class-map: class-default (match-any)
      3809 packets, 435025 bytes
      30 second offered rate 0 bps, drop rate 0 bps
      Match: any

Regards

Dinesh

[lgijssel]

Hi Dinesh,

It seems to be working.

Can you please verify the IOS version on your box?

regards,

Leo

[dinesh2001]

Hi,

I am using:

IOS (tm) s72033_rp Software (s72033_rp-IPSERVICESK9_WAN-M), Version 12.2(18)SXF12a, RELEASE SOFTWARE (fc1)

router6509>sh policy-map interface
GigabitEthernet4/3

  Service-policy output: WAN_QOS

    class-map: CLAS-TRAFFIC (match-all)
      Match: access-group name TRAFFIC-ACL
      police :
        2000000 bps 62000 limit 62000 extended limit
      Earl in slot 1 :
        218 bytes
        30 second offered rate 0 bps
        aggregate-forwarded 218 bytes action: transmit
        exceeded 0 bytes action: drop
        aggregate-forward 0 bps exceed 0 bps
      Earl in slot 2 :
        0 bytes
        30 second offered rate 0 bps
        aggregate-forwarded 0 bytes action: transmit
        exceeded 0 bytes action: drop
        aggregate-forward 0 bps exceed 0 bps
      Earl in slot 5 :
        1626710555 bytes
        30 second offered rate 81736 bps
        aggregate-forwarded 1626615647 bytes action: transmit
        exceeded 94908 bytes action: drop
        aggregate-forward 77376 bps exceed 0 bps

    Class-map: class-default (match-any)
      5700 packets, 671208 bytes
      30 second offered rate 0 bps, drop rate 0 bps

Regards

[snt_vdc2noc]

Dear all,

I'm facing with a problem about monitor traffic for each class of service when i apply poilce on my Tengiga interface. The output command result as below:

7600#sh policy-map inter ten4/4

class-map: Hosting-Colocation-to-Network (match-any)
Match: access-group name Hosting-Colocation-to-Network
police :
10000000000 bps 31250000 limit 31250000 extended limit
Earl in slot 4 :
13801619258245 bytes
30 second offered rate 144487304 bps
aggregate-forwarded 13801619258245 bytes action: transmit
exceeded 0 bytes action: transmit
aggregate-forward 145773304 bps exceed 0 bps
Earl in slot 5 :
72837 bytes
30 second offered rate 0 bps
aggregate-forwarded 72837 bytes action: transmit
exceeded 0 bytes action: transmit
aggregate-forward 0 bps exceed 0 bps

class-map: class-default (match-any)
Match: any
police :
10000000000 bps 31250000 limit 31250000 extended limit
Earl in slot 4 :
74520070218188 bytes
30 second offered rate 879718984 bps
aggregate-forwarded 74520070218188 bytes action: transmit
exceeded 0 bytes action: transmit
aggregate-forward 888842536 bps exceed 0 bps
Earl in slot 5 :
5622549680569 bytes
30 second offered rate 93300336 bps
aggregate-forwarded 5622549680569 bytes action: transmit
exceeded 0 bytes action: transmit
aggregate-forward 99314912 bps exceed 0 bps

!

My traffic have 2 type which classify to 2 class as above. I would like monitor traffic at fields bold (30 second offered ...). Pls advice me how to monitor this field on graph.

Thanks and best reagards,

Vo Minh Thuan