Hi,We are in transition period migrating from one internal PKI to a new Internal PKI. Existing flexvpns are setup with certificate from the old PKI CA for IKEv2 tunnel protocol. We're bringing online a new flexvpn that has the certificate issued by...
Forum Posts
Please can a member make some time guide/help.I have a range of Cisco products set up and working on my SOHO; I purchased two additional APs and part way through configuration the CLI session would not start.PuTTY window opens, black background stati...
I hope I'm in the right spot......We have a number of Cisco switches and routers from older 2950 switches and 4400 routers to our newest 9300 switch. We have the console port connected to console management switches via RJ45 to serial cables. The con...
Hello,I have a problem that's really bothering: I have a Cisco WS-C3850 L3 switch and I want to use it (partly) as a router: The network:I can ping from 10.9.0.3 to 10.9.0.1 and vice-versa.The problem I'm facing: when trying to ping from the firewall...
Resolved! Routing to and from VLAN
I have Cisco SG550XG switch-Switch network overview - I have assigned IP address of the switch as 192.168.64.21 and have created a VLAN for some ports IP 192.168.65.21. Now currently I have 64 and 65 subnet to use, but the issue is How to allow routi...
Dear Team, We are having POE Pds and the Team is looking to connect the POE PD devices in Ring topology. 1. Is the POE PSE ports are one to once connection or possible to connect multiple PDs into one PSE2. Please suggest POE PSE support Ring topolog...
hI, I want to sell a new memory and disk from another/new partner. i can use the contract support for memory and disk since blade from original partner
HelloI know it is possible to configure Dual Hub Dual Cloud with 1 underlay - is it explicitly mentioned anywhere that you should use a different SP (underlay) for the second cloud? I know that logically it is better to do so - just wondered if that ...
Hello, We have Cisco 2911 appliance, and we need to renew its security license. What is the part number of the license to request it, or how to know the part numbers from the appliance to do it.Thanks
Hello,i am trying to Upload the image from an FTP server to a cisco catalyst C3850 and i am having the below error message% Connection timed out; remote host not responding%Error opening scp://*****@****/cat3k_caa-universalk9.16.12.05b.SPA.bin (Unde...
folksi've moved from snmpv2 to snmpv3 and i'm no longer seeing any events on my snmp serverwhen i run a packet capture i can see my router sends a get-request to the snmp serverthe snmp server, spectrum, then replies with a 'report' but i suspect wit...
I am confused about a DHCP config. I have a scenerio where I have two physical ports working as Router on a Stick for the same VLANs on a Cisco router running DHCP. I want both sets of subinterfaces to pull IPs from one set of DHCP pools. From my und...
I am puzzling with a redundant setup with HSRP. (See image in attachment).There are three pc's connected to a switch. One pc in VLAN 10, one pc in VLAN 20 and the last one in VLAN 30.Out of the switch there are two ports (g0/1 and g0/2) connected to ...
I've been struggling to understand the best practice for load balancing (per host) on multi-homed networks. Ensuring that the load balancing is based on the host is crucial because sessions do not work properly if split between separate ISPs. I am wo...
Enter cli config mode and load config via http or https. Can't get it work on a ncs router. Getting 404 for http and ssl error for https. Tried also escaping ? with \. Both http and https urls work fine from other clients like curl.
