Hello, I want to make sure that the special RJ45 connectors that I am considering will fit side-by-side on a Cisco switch. What is the physical distance between ports on Cisco switches, or this switch in particular?
Hello, I want to make sure that the special RJ45 connectors that I am considering will fit side-by-side on a Cisco switch. What is the physical distance between ports on Cisco switches, or this switch in particular?
please help me . i have done my ccna & am planning to do my ccda. i dont know how to start & what to refer to or how to practise . help!
Hello all, I have a hopefully quick question. I have recently begun to use the Cisco 4351 ISR in our networking setup. I am looking for a method or process to test the ASync break out cables from the NIM module to the DB-25. Our current process ...
hello dears i have 2960 switch and its suddenly stops booting and its reload continuously .so I tried to load new IOS using xmodem , but the same problem remains. i tried 5 different versions but all the same (i have download the images from cisco ...
Hello, I need to block ingress ntp and snmp traffic from the Internet to a few IP blocks our company owns and live inside our network. The ACL needs to be created on an ASR1001. Here's the ACL I created but I am not 100% sure if it is correct. Do y...
Hello Expert, can someone please explain me How to TRUNK Between CISCO 2960 and 3com 5500g ? But I am not able make this work. Thanks for your Help
Hello, we are trying to stream some video between two Crestron-Devices, one transmitter (10.43.1.66) and one receiver (10.43.1.90). I configured multicast routing via Pim sparse mode with a rendezvous point. After about 2 minutes the stream stops. If...
Hi All, I have two identical catalyst 3750 switches, one is in production, the other is brand new. Both have the same software versions installed on them. I copied the running-config off of the switch that is live on our network and saved it onto a...
Hi, It's possible to create a backplane stack between two SG-550x (one 24T and the other 24F) and three SG-250x (48T) switchs? I need both management and LAG working on the stack... it's possible? Regards
I have configured L2TP vpn to Private Internet Access (PIA) on my router but the virtual-ppp1 interface is up but line protocol is down. I have been over my config and can't figure out what is wrong. I have a dialer interface to my ISP and that is ...
Hello, Does anyone know how to connect a multilayer core switch to a router in a way so that any traffic whose destination is not known inside the network of the switch is directed to the router? Thank you!
Hello Everyone, Here is my C6832-X-LE VSS switch log , I could not find anything related or any lead to this log and need help to reach the problem, I appreciate if you share your comment for this problem and on the other hand the port does not ope...
Hi, I've been trying to solve this problem for a quite long time and I gave up. I need some help ;) I have two devices on my desk: C6500, sup720, pfc3c, msfc3 and C7600, rsp720, pfc3cxl, msfc4. Both are connected with a wire. Both ports are switchpor...
Hi Experts, Would like to clear a doubt. With a setup of two 9K series Nexus Switches running vPC peer link between them. A server is connected at access end of these switches. Just taking example. Switch-A and Switch-B are interconnected and ...
Hi guys I trying to figure out how to enable egress traffic in a icmp flow Here the scenario, 2 routers Fa0/0 Fa0/0 RA -----------...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
02-20-2024 07:45 AM | ||
02-15-2024 09:08 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM |