Hello,I have a network setup as follows: nat inside nat outside 207.x.x.x--router ----(FE0) main router (S0)------ router --- 10.72.1.0 (S1) ...
Hello,I have a network setup as follows: nat inside nat outside 207.x.x.x--router ----(FE0) main router (S0)------ router --- 10.72.1.0 (S1) ...
Can anyone help me.I need upgrade my core switch (5505), because I have limit of gigabit ports and no free slots in chassis. Moreover I have configured IP MLS and IPX MLS for VLANs with external router3620 (4x100TX). I stay on new line of Cat 4500 s...
I need to upgrade a Cat 6509 MSFC1 to the CatOS 7.x.xsoftware for use some new features!Which IOS + CatOS images are raccomanded at this time(the switch hat just 64M RAM for sup1 and MSFC)Best RegardsA.Calligher
I have a branch office connected to a main office over a 128K frame-relay connection. The branch office runs a mission critical application that requires only 28K of bandwidth to run normally. When a user at the branch office checks email, the miss...
Where can I find the part number for this IOS Image 12.2(15)ZJ. Thanks
4 tunnel interfaces configured (2) 7206VXR at each site, 2 for primary site and 2 for disaster site. Receiving errors in syslog that the tunnel interfaces @ primary site are dropping (usually several at a time and see to be geographically listed east...
Hello,I use a serial line to connect a site to another site within a distance of 6 km.I use cisco 2600. Wen showing interface for this line i see in local interface 2% error, and in the other side 90% errors (crc,frame). This the output i see:Serial0...
Is it possible for incoming calls to a Bri interface in one router to utilise the Mica Modems located in another router.I think that the answer is no as calls are tied to tty ports.Please can someone confirm.ThanksSimon
Hi,I have a 2600 router with two interfaces. Is there an easy way to find out what conversations take place from one int to another, and what ports are used? I tried this making an access-list 'permit tcp any any log' and 'permit udp any any log' but...
We have a 3662 router with an ATM card in it and 3 ethernet ports. The ATM had about 100 sub interfaces on it, and most of the regional sites are allowed to connect to just one of the networks on the ethernet side (say port 1). We have 1 ATM subinte...
Hi,Does anyone know if you can configure/use the 10/100 mgt port on the 4500 Sup4 for out-of-band management/software downloads etc.I do not see any reference to it using cat4000-ik2s-mz.121-13.EW1.bin. There are no Fast Ethernet interfaces listed.No...
I copied the configuration from my routers or switches.Now I would like restored back the config to my routers or switches.I have done using copy tftp startup-config and at the same time activated the tftp server.It's not working any advise or any g...
Hi,We have IOS routers (12.1(16) that make and receive hundreds of ISDN calls per day. The routers also have a number of serial interfaces. These routers are logging events to a syslog server.We do not want to fill our syslog server with logs assoc...
This means that catalyst 1900 support RIP routing protocol ?How do catalyst treat RIP routing update ?
Does anybody know how to connect to the 7500's linecard??just like the "attach" command on the GSR.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:
Subject | Author | Posted |
---|---|---|
02-20-2024 07:45 AM | ||
02-15-2024 09:08 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM |