Other Network Architecture Subjects

Hi, The problem is that I can’t configure trunk on 2924(because there isn’t any command with trunk) and if I configure the interface of 2924 with switchport mode multi-vlan and 4506 with switchport mode trunk , the protocol is down,What is the solu...

Hi,We are using a setellite link which is simplex without return path. We have connected a Windows media server at one end of the link ( multicast streaming ) and at the client end a windows media player.The line protocl at the both the end of the ro...

Hi, I have a configuration hub and spoke withi frame relay, in the core a 4000 and the others sides, 1751.When i check with the command sh frame-relay map in the core, 4000, i can see the router 1751 and it IP and DLCI, but i can´t ping it.When i che...

Hi, i have a 7507 router with OC3 Interface and I connect this to a 5500 Catalyst Switch. I configure a ip address and mask of interface, but in a host on the same Vlan i try to make ping to ATM Interface an this dont response. Can give me steps to ...

Two issues:1. BBSM is not killing old sessions, but reissuing the same IP address elsewhere. When this happens, the client's location is listed as the place the IP address got reissued to. Could this be a problem with the BBSM database not refreshi...

Guys,i need set the timezone for NTP for GMT + 0100 timezone (paris)Can anyone help me with the command, please.thanks

One of my customer try to code an snmp tool and has this problem :With 2950 switcheswhen positionning port (port 29) in vlan 260 instead of 114. Under solaris v9/usr/local/bin/snmpset -v2c -OQ -c rwcommunity SWITCH_IP_ADDR .1.3.6.1.4.1.9.9.68.1.2.2...

Hi,When I use the traceroute command on a Cisco router, I often receive the next response:router#trace 192.168.3.21 192.168.1.2 20msec2 192.168.2.2 25msec3 192.168.3.2 20msec * 20msecWhy the is a " * " in the result, so that the traceroute is...

I have a number of routers (1700, 2600, 3640) that I manage in remote locations connected by Frame Relay links. I have no problem downloading or uploading either configs or images to any of my routers but the 3640's. I have tried using defferent tftp...

Hi,Just installing RTM in our lab. I've enabled RMON on my CAT 4006 Sup II CatOS 7.3.I've added the switch to the RTM Server but I have problems with monitoring it's traffic.When I try to check statistics in the Traffic Monitor all, but 'TopN Links' ...

If I assign the IP address 1.0.0.1 subnet mask 192.0.0.0 to e0, what is the next IP address in this logical secquence that I could assign to e1?EX of above question using a class C IP address:192.168.1.17 255.255.255.240 on E0192.168.1.33 255.255.255...

I want to establish the next thing. I am using the Cisco Dial Out tool to make a COM connection via TCP/IP to an access server 2503 with an ISDN interface.The problem I face is that I can not access the access server via poort 6001. If I do a port s...

I have GigaStack'ed a 3550 a 3524 and a 3548 together with 3 cables. I need to set the 3524 Gigastack link 2 as redundant link , but there is a specific command to do it ? How it decides which is the redundant link ?I believe its cause of the mac add...

Hi,we have the following scenario: two Cat4K supIII in a redundant fashion on a Server Farm. We have one server with 3 NIC connected to switch A and another server with 3 NIC connected to switch B.These two servers use compaq NIC Teaming SLB and form...

Hi I have created a new fastethernet interface in dot1q vlan trunking (as you see below) on my router, then I want monitor the amount of traffic going through this interface using MRTG. Surprising me I see in the MIB walk no new interface has been c...