Up to now I'm still confusing function of default-network command :ip default-network <network>What is the different between default route and default-network ? Thank a lot.
Up to now I'm still confusing function of default-network command :ip default-network <network>What is the different between default route and default-network ? Thank a lot.
hi can any body send Inter service provider configuration for Study purposei really thanks ful that person
I have several 2620's that I need to upgrade to 32mb of Flash. With the Flash upgrade, comes a ROM chip. The problem occurs when I replace an older ROM chip with the newer chip included with the flash. When we boot the router, we see absolutely no...
Does anyone know of a way to assure that IcServer does not start? I would not be adverse to moving a file or two if this would help. I browsed the documentation and other than manually shutting it down could find no reference.Thankspat
Hi,I have a serial interface configured like this:interface Serial3/1 ip address 192.168.112.100 255.255.255.0 encapsulation frame-relay frame-relay interface-dlci 143 frame-relay interface-dlci 146 frame-relay interface-dlci 151and I´d like to set i...
Hi all,Our cisco6509 has 20 vlan interfaces with internal IP addresses set. I place an "ip route 0/0 0/0 172.16.1.1" to forwad these packets to an NAT server(172.16.1.1). Now I need to add a vlan interface with IP 100.1.1.1(formal IP). Of course, I w...
Hi,I hope someone can point me in a direction how to configure 1721 for Adsl(which I use now ) but the same router to have dual login scripts,so that I could set a session for VPN into intrenet connection and other session for internet connection .Th...
I have a 1601 router configured to accept ppp-chap calls.It is configured with a default gateway and this should remain unchanged.What is the most 'elegant' way to configure the dialer to make the ppp client follow a different default route without ...
I have three routers in a full mesh point to point architecture. Two of the three routers have an extra T1 that is bound to another T1 under MPPP. In my routing table this MPPP circuit is selected as a feasible successor to each of these two routers ...
Can anyone give me a hint on configuring IPSEC and what IOS I need. Company is setting a sattelite antenna to between two of our building. The connection to me is just a ethernet cable. Do I need IPSEC for wireless oror just plain IPSEC.
As I search in cisco.com and found that seems 1720 hardware not support 802.1q. Is it true?
Is there a way to dump the contents of the DNS cache to a file in CNR?
hi, guys,We are setting up a backbone network right now. we are using two 4506 super IV as the central switch (each with one 24 port 10/100/1000 module), and using nine gigastack 2950 switches.The port connection is like this:ws-g5484(4506 - I ) -- w...
i want to know whether cat 6000 switchs support vmps server. following is from cisco document :Catalyst 6000 family switches support VMPS client only. You must have a Catalyst 5000 family switch as the VMPS server to configure dynamic port VLAN mem...
Can I make a single interface to bahave as NAT inside as well as NAT ouside. Can it be done by subinterfaces
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:
Subject | Author | Posted |
---|---|---|
02-20-2024 07:45 AM | ||
02-15-2024 09:08 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM |
User | Count |
---|---|
3 | |
2 | |
1 | |
1 |