Hi guys, I'd like to ask if there's another way to show users activity other than show ip cache flow. I can only see he uses 1F90/8080 (HTTP) but i can't verify on its destination port if what site does he opens. Thanks.show ip cache flowSrcIf ...
Hi guys, I'd like to ask if there's another way to show users activity other than show ip cache flow. I can only see he uses 1F90/8080 (HTTP) but i can't verify on its destination port if what site does he opens. Thanks.show ip cache flowSrcIf ...
Hej,I am in planning of LAN re-design for Head office which consists of different networks - user LAN, WAN, DMZ, Internet, Special connection, sever LANPresent traffic generation across the networks, ofcourse in near by future these values except to ...
HIHow to configure one router to get time from NTP server using Lo1and provide time using Lo2 ?
I have no idea how to close this post so I am just deleting the question as I have asked it somewhere else and a few forum people had their panties up an a bunch about it....
HII am having some problem with 1841 router. I deleted its image and now tying to download it from TFTP in rommon. I am getting these messages.Readonly ROMMON initializedrommon 1 > IP_ADDRESS=192.168.1.3rommon 2 > IP_SUBNET_MASK=255.255.255.0rommon ...
hi all,i've a bgp router with Gigabit Interface and a internet circuit of 100M ..sometimes occour that the internet link go in saturation (downlink only) and the lacency go up ..i've tried to setup a qos with class-map on GigabitEthernet0/0 (facing i...
Dear,I have a home lab wthe a 2600 access server (16 port octal). From this 2600 router I want to connect to a Raritan 8 ports RPC.This RPC (Remote power control) has a rs232 serial port (RJ45)I tried a lot and still I do not get connected to the RP...
Hi,I recently purchased a Cisco 4402 on ebay and I have v3 software on it currently and have no way of upgrading it without downloading the software from the cisco site - which I don't have access to as I don't have warranty on it and don't wan't to ...
Hello all ,I have come across this doubt recently , while i was assigned a "Revamping" project for a legacy network.As part of a temporary setup , we are required to connect two swiches :A. 2950 switch with MTRJ port types for fibre.B. 2960 S seri...
Hi guys, i've been doing an EEM scripting were an email action in an applet to send the email and use the syslog event detector to match your syslog message. Below are my config:ROUTER(config)#event manager applet mode-downROUTER(config-applet)#event...
We recently completed the steps to recover password on a 2960G switch as per instructions found at http://www.cisco.com/en/US/products/hw/switches/ps628/products_password_recovery09186a0080094184.shtml Four password were changed as per documentation...
Hi Expertwhether cisco prime infrastructrue same like splunk software?or both the above software different ?Thanks
At my work, we are trying to choose between Dell and Cisco for our network upgrade. Dell has got Cisco beat on the price and a lot of the specs too.Our current setup:Core: Cisco 4510 1Gbps copper to servers 1Gbps fiber to 4 network close...
Hi, everyone! Our client has an office building, which he rents out to its customers.The customer plans to provide internet to its tenants. It is planned to 30 clients, and the total channel capacity of the provider 300MbOn the border with the pro...
I have a switched network of C2980 & C3548 switches with multiple VLANs. I would like to understand the difference between Mulit-VLAN ports and trunk ports.What circumstances would dictate using one over the other?If I configure the router port as M...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
02-20-2024 07:45 AM | ||
02-15-2024 09:08 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM |