Hello, We have Cisco 2911 appliance, and we need to renew its security license. What is the part number of the license to request it, or how to know the part numbers from the appliance to do it.Thanks
Hello, We have Cisco 2911 appliance, and we need to renew its security license. What is the part number of the license to request it, or how to know the part numbers from the appliance to do it.Thanks
Hello,i am trying to Upload the image from an FTP server to a cisco catalyst C3850 and i am having the below error message% Connection timed out; remote host not responding%Error opening scp://*****@****/cat3k_caa-universalk9.16.12.05b.SPA.bin (Unde...
folksi've moved from snmpv2 to snmpv3 and i'm no longer seeing any events on my snmp serverwhen i run a packet capture i can see my router sends a get-request to the snmp serverthe snmp server, spectrum, then replies with a 'report' but i suspect wit...
Hi All, I have a CSSM server in DC with available licenses. I have few ASR 920 routers in another building which dont have any internet access. Is there any way to license this ASR's without connecting to internet? I do see there is an option to do o...
I am confused about a DHCP config. I have a scenerio where I have two physical ports working as Router on a Stick for the same VLANs on a Cisco router running DHCP. I want both sets of subinterfaces to pull IPs from one set of DHCP pools. From my und...
Greeting everyone,I've been searching for a method to identify the prefixes advertised by BGP without specifying a particular neighbor. Is there any command for this issue ?Thank you
I am puzzling with a redundant setup with HSRP. (See image in attachment).There are three pc's connected to a switch. One pc in VLAN 10, one pc in VLAN 20 and the last one in VLAN 30.Out of the switch there are two ports (g0/1 and g0/2) connected to ...
I've been struggling to understand the best practice for load balancing (per host) on multi-homed networks. Ensuring that the load balancing is based on the host is crucial because sessions do not work properly if split between separate ISPs. I am wo...
Hi, below is the "show ip mroute" output in question: (10.198.184.6, 239.255.100.1), 1w1d/00:02:53, flags: T Incoming interface: Port-channel300, RPF nbr 10.199.6.33, RPF-MFD Outgoing interface list: Vlan990, Forward/Sparse-Dense, 01:31:51/stoppe...
Enter cli config mode and load config via http or https. Can't get it work on a ncs router. Getting 404 for http and ssl error for https. Tried also escaping ? with \. Both http and https urls work fine from other clients like curl.
Has anyone tried putting a VIP or fronting Cisco Secure Network Analytics UDP Director with a VIP? I have 2 UDP at 2 separate location and would like to put a VIP. Any information or documentation would be really helpful.
Has anyone ever routed by port number.
My C8300 router is in a loop for "hardware initialization..." Unable to break the loop and enter either rommon or startup config.
Hello,I try to setup a dial-in server with 3825 router and NM-8AM-V2 card. but I am facing some issues. The purpose is to allow incoming connexions from various devices who still use analog modem connexion. These devices are directly connected to RJ1...
Hey,I have created a custom firmware using the FDK provided. for Exanic X25 everything works properly and both the ports (port 0 and port 1) link is up. but when i generated the same firmware for Exanic x10, the port1 link is always down. Is there an...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:
Subject | Author | Posted |
---|---|---|
02-20-2024 07:45 AM | ||
02-15-2024 09:08 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM |