Question:Dual RSPs: Does NVRAM and SLAVENVRAM have to be the same size for Sync between the two to function properly??ThanksVince
Question:Dual RSPs: Does NVRAM and SLAVENVRAM have to be the same size for Sync between the two to function properly??ThanksVince
I've a topology where I've remote locations with frame circuits back to a central facility with redudant infrastructures. The central facility has two 7200, one with dual circuits to AT&T and another with dual circuits to MCI. The remote facilities...
Unable to access router via telnet. The telnet password lets me in, but can not enter EN mode says 'no password set'Must be a common problem, but I can not get around it.
I have many 2501s connected via Frame Relay to two core routers. All of the sites show up when running the command: "sh ip eigrp neighbors"...except one. I can ping the router but can't login. TACACS+ fails due to this apparent EIGRP failure or pr...
Hi everyone, please i need to know if putype=1 (no xid sent from remote device) is supported with qllc (IBM SNA over x25) configuration ios 12.1.If the answer is yes why nothing happen if i specify qllc xid vmac ..... (the same in switched major node...
Hi.I have a Cisco 2621 running IPPlus IPSec56 with a 1710 and 1720 connecting to it with crypto Ipsec tunnels. I have recently had some problems and have found in troubleshooting there are different ways to configure this setup and would like to kno...
Hi.I have the following problem.We have ONE router 3640 with NM-1FE1CE1U= card.Working in a HUB & Spoke Network (Point Multi Point).But we need to provide support links.To do this we buy another 3640 but now with* TWO of - nonort F. Ether. 1Port Cha...
Hi,I checked the cisco document, the tokenring switch 3900/3920 uses hexdecimal as the ring number, while the router tokering interface, it use demimal ring number, is there any in-consistancy? don't I need to convert them when doing configuration?Th...
I have been trying to configure a Linksys BEFSR41 to work with my Cisco 675. After some time with Linksys tech support, they told me the two were not compatable. I would love to hear from others who have this confirmed or have got their Linksys to wo...
Whe are using CW 2000 on a w200 server.Each time we start The ANI server it starts ok, but after a few minutes it says that there are some problems. This problem started after the activation of a second ethernet card. Did somebody had the same proble...
Hi, i need span a port (Fast Ethernet) on a Catalyst 6509, i have two vlans, and when i set the port to span, the port gets down, and it doesn't work...... someone have some idea?i did this question yesterday, bun no answersplease help me...o m a r g...
Hi, i need span a port on a cat 6509, i have two vlans, and when i set the port to span, the port gets down, and it doesn't work...The switch has a crossover cable between 2 vlans (yes, i know, but i didn't do it, and its working) and i cannot touch ...
I'm curretnly preparing for somecustomer presentations. In the tehnical direction there is no problems for information. But in my opinion there is a problem with marketingand "why to use" infromation related to customers and for CTE level ppl (not fo...
Ok, first off, I know hardly anything about this but got stuck doing it anyway.I'm attempting to setup a cisco 806 with NAT. It will be connected between a DSL router and the LAN to provide internet access to stations on the LAN. I have to do the rou...
Hi, When I configure ipx over frame-relay multipoint interface, I need to run eigrp and disable the split horizon, and I'm running ipx rip on the same router thus, redistribution is automatic by default. This will cause potential routing loop when th...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
02-20-2024 07:45 AM | ||
02-15-2024 09:08 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM |