My C8300 router is in a loop for "hardware initialization..." Unable to break the loop and enter either rommon or startup config.
My C8300 router is in a loop for "hardware initialization..." Unable to break the loop and enter either rommon or startup config.
Hello,I try to setup a dial-in server with 3825 router and NM-8AM-V2 card. but I am facing some issues. The purpose is to allow incoming connexions from various devices who still use analog modem connexion. These devices are directly connected to RJ1...
Hey,I have created a custom firmware using the FDK provided. for Exanic X25 everything works properly and both the ports (port 0 and port 1) link is up. but when i generated the same firmware for Exanic x10, the port1 link is always down. Is there an...
HiI'm looking for the correct CCNP Encore discussion board where I review questions and answers posted by fellow students as well as poting my own.Is it this page? https://learningnetwork.cisco.com/s/ccnp-enterpriseThanksLasse
Hey Everyone, I currently have my archive set up to tftp to an off site server. As I work in a lab/dev environment I need to go back and look at configs as far back as 5 years ago, to see how things might have been set up for a test we were running b...
Hey Cisconians!I kindly ask for some help with a config on a Cisco ASR1001 router. I have a 10G fiber link from this router that is connected in our cage and the interface shows UP/UP at the moment. I cannot adjust speed and duplex or Encaps 802.1Q o...
Hello, I would like to know if you could share a link or file with which I can understand what would be the limit that we should respect to maintain a diffusion domain and that this does not affect the network? I know that the idea is that very large...
Does anyone know how to logout and clear PSTN session when we login via US Robotics modem?PC ---- US robotics modem ----PSTN line ----- US Robotics ------ C1111 RouterThe above is the network diagramu.I could login to C1111 router through the modem, ...
Hello,I have a XPS 2200 on hand and I was wondering if power supply PWR-C1-715WAC-P is compatible with the XPS 2200 as we dont have the correct part number/power supply referenced in the doc for the XPS. The PWR-C1-715WAC-P is for a C9300. XPS Corre...
I am using the latest version of packet tracer but still getting compatible issue and I can't find anywhere any solution of it anywhere if anyone knows how to open this file please help !! I am also dropping the file please if any know how to open, t...
How do you add new devices to the list of devices in Packet Tracer. Specifically Switches that are not on the list?
Hi,I got a 2503 with an apparently dead console port. I upgraded the IOS in the router and did a write erase (via the Aux port). (Please don't ask why I did a write erase when I knew the console port was dead ... I was being a user ;)Now that it has ...
can someone tell me what is the mistake I did
I am having an issue with my GNS3 VM version 2.2.42. Anytime I increase the Memory size and the CPU Count in settings -> system, the change is not registered and will revert back to previous settings when turned on again. Anyone have an idea why this...
Hello,I have encountered a strange issue related to the hsr-ring interface (comprised of g1/3 and g1/4) on IE4000. In case both links get disconnected and the switch is rebooted, I have observed that although the hsr-channel's interface goes up as so...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
02-20-2024 07:45 AM | ||
02-15-2024 09:08 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM |