Bonjour, dans l’entreprise sur l’utilisation du réseau Cisco assistant version 6.3 , je voulais voir quel port du switch principal du réseau, est connecté avec un autre switch et on voit pas le lien de connexion avec un autre groupe des switch. Ces d...
Forum Posts
I am using the below configuration on Catalyst 4500 series switches will this work?logging onno logging consoleno logging monitorlogging buffered 123456logging host 1.1.1.1logging host 1.1.1.1 transport udp port 123logging source-interface loopback0l...
I'm having issues SSH'ing from a Cisco 3925 router to a FIPS enabled and hardened Linux server. The Cisco 3925 is on IOS version 15.7(3).M7. The Linux server (RHEL 7) is configured with the following defined in its SSH server config: Ciphers aes128-c...
I have two routers/firewalls in active-passive mode which have two nexus switches connected. The two nexuses in VPC then have one link each to edge switch. The nexuses have servers connected and they serve video streaming to clients connected to edge...
Hello everyone, I am currently having an issue with this lab I am working on in packet tracer. I have around 14 hours into this and cannot seem to find out why I am having issues.This is a Lab with HSRP for 4 Vlans, 10,20,30, and 40. Overall, I have ...
Resolved! Which device to buy...
Hi, I am trying to find a router and an Access Layer 3 switch as well as a Wifi 6 AP for the SOHO area.When I bought cisco devices in the past, the management was always very different.For example, the SG 300 switch has a very limited IOS but can be ...
Hi, learning to use packet tracer,. I'm on chapter 3.1.1.2 Viewing the Contents of PDUs. So I am creating a complex PDU as per video but on the 2.1.1.5 simple network. Doing everything as in the video then pressing play but my PDU always starts as pi...
Hello All! A network with a hub and spoke WAN. The remote routers are connected via a Metro E. and then connects to the hub router. My question is: Is there an advantage of using a /30 for each connection or just use a /24 besides saving IP address...
Hello, I've written a small EEM script to send an snmp-trap when a specific route is removed from the BGP routing table: event manager applet EEM_TEST_DOWN event routing network x.x.x.x/32 type remove protocol bgp action 1.0 snmp-trap strdata "<notif...
Hello all,I am curious as to whether cisco has an official topology for CCNA and CCNP. If so, where can I find this information. If not, are there any suggestion for other topologies to use. Thanks,Dave C
Cat6506 Version 12.1(11b)EVLAN filter applied to one VLAN. Forwarding and dropping works fine but DHCP Requests from clients to DHCP-Server within that VLAN doesn't work.Any Idea?Thanks in advance.Daniel
I am engaging a very large new smart campus (around 10 sqm, 20 large buildings, 2 train stations, multiple bus stations, and lots of audio visual devices) network design competition recently. Some system integrator proposed the Corning One GPON/XGPON...
Can someone help me with the network design of a big internet cafe that has these 3 things below (see picture below) and with an IP configuration? 15 computers or 10 will do.
I have a catalys and they asked me to configure IPTV.How can I configure this?
Resolved! Help ISR4331 not recognizing LTE card
Trying to bring up an ISR4331 that has 2 - LTE cards installed in it. When I type LTERouter# show facility-alarm status, I see that the LTE cards which are installed in subslot 0/1 and 0/2 have a "Critical" alarm and in the description it says "Activ...
