hello, could someone confirm that it shouldn't work , or am I wrong ?I have CISCO IE which is translating private addresses ( machine network ) to public ( common network ) . Common network is VLAN 10, so access port are assigned to this VLAN, and on...
Hi, im wondering if this architecture is even possible. I have 2 routers R1 and R2. R1 is the RP and is connected to R2. Im using sparse mode to pull the multicast feed from the RP to R2 and reflected with a new Multicast group via a Virtual Interfac...
Hi all....... I have an ISR4000 series with EN140N UCS module. Windows server was running on it fine booted up ok.After a power cut the server will not boot. It seems to have lost the option to boot from the SSD. every option seems to go round in PXE...
Hello, I'm currently a new student in packet tracer and i believe I've done all the necessary configurations needed for the network design attached below. I've done Vlan, IP configuration, IP DHCP excluded and router rip. But i can't seem to make the...
Hi Guys. I have two QSIG Links to the Third Party PBX. Thus 2 * separate 30 Channel Links between the PBX. I want to group both the 30 Channel, in the dial peer when dialing out to the Third Party PBX. But the dial peer only allows one Port. Note - ...
i am new to this and learning by doing on the waywhat i try to achieve in the moment is to reroute the port 80 on pc 0to 100 on pc 0 this is how i forward external internet trafic to itip nat inside source static tcp 10.1.1.1 100 interface Cellular0/...
I have deployed a linux server to ENCS with two interfaces "eth0" and "eth1" with IP addresses 10.0.10.132 and 10.0.10.133. There is an external router in my network as ERSPAN source generating traffic and configured to send ERSPAN to ip 10.0.10.133....
Hi all, I have these 2 questions looming in my mind for some time. Please throw some light on these.1. Can the terms SA and tunnel be used interchangeably?2. What is the exact purpose of doing a'a crypto ipsec sa'? Can we say that it is done due to ...
Strange? Just installed 7.3.1 and tried to open a *.pka file created with 7.3.0.... Not possible: "This file is not compatible with this version". Tried files created with older versions -> works fine.So whats wrong here?regardswerner
Hello Everyone,We have several office networks connecting to the internet each using a single ASA 5506 or 5508, depending on the office. We are looking to eliminate the ASA as a single point of failure and trying to consider all options, factoring in...
Hi i a seeing the following what can i do to resolve. Oct 15 10:49:48 EST: %BGP_SESSION-5-ADJCHANGE: neighbor 10.2x.x.x IPv4 Unicast topology base removed from session BFD adjacency downOct 15 10:50:08 EST: %BGP-5-ADJCHANGE: neighbor 10.x.x.x UpOct 1...
Hi All How can I remove main-cpu command? redundancymode nonemain-cpu standby initialization delay 30 xxxx(config)#redundancyxxxx(config-red)#no ?application Enter application redundancy group modeinterchassis Enter interchassis modelinecard-group...
I am trying to get additional details on BGP and or OSPF DISTRIBUTE-LIST ROUTE FILTERING using the SPECIAL EXTENDED ACCESS-LIST. Yes I am aware that route filtering can be accomplished using prefix-list but I've heard the CCIE LAB may require the acc...
Hi ,I would like to ask about reverse flows error. I saw the same issue in forum and try to fix. But i don't know how to add NAT Exemption rule or my exemption rule is doesn't work.my network information : inside-net=20.1.1.0/24outside-net=10.1.1.0/2...
To me, the Cisco implementation of LLDP seems extremely broken. I would love to find out I’m wrong and there is a way to use it effectively. However so far my experience is as follows below. This is all on the SG300, SG350, SG350X and similar seri...
