Can you teach me setting the booting OS (WS-SUP720-3B)

[Soon Kwan Kwon]

Actually, I already posted about WS-SUP720-3B.

But, at that time, The problem is the SP. I could see through the show version.

However,, I have another SUP. and I booted up it.

It was continuously entering the ROMmon mode...

So, I was also continuously manually booting the SUP.

------------------------------------------------------------------------------------------------------------------------------

I inserted flash memory in the disk0 slot..

I performed below commands one by one.

boot system flash disk0:s72033-ipservicesk9_wan-mz.122-18.SXF16.bin

boot system disk0:s72033-ipservicesk9_wan-mz.122-18.SXF16.bin

AND rebooting?

I could see the ROMmon...

rommon 1 >

------------------------------------------------------------------------------------------------------------------------------

I upload "show version", "remote command switch show bootvar", "show bootvar".

and I also upload rommon 1 > dir disk0: which is a evidence to be stored IOS.

After you show uploaded photos, plz give me a good idea....

Thank you:)

Cheers.

Edited...

Although I input command "boot system disk0: ~ " and "write memory", 

and rebooting, => there is no command boot system disk0: ~ in the show run...

About this, you can see the boot_system_disk0.png

ah.. It is very difficult.. hard work

[vivek srivastava]

can you post the output of "dir" once router is booted (i.e. in # prompt)

[Soon Kwan Kwon]

Here is what you ask me photo!

[vivek srivastava]

Save the config after below and reload.

!
config t

boot-start-marker
boot system flash disk0:s72033-ipservicesk9_wan-mz.122-18.SXF16.bin
boot system flash bootflash:
boot-end-marker
end
wr
!

 

[Soon Kwan Kwon]

Oh Ok I'll give it a try and let you know whether it is working properly or not :)

[vivek srivastava]

Also, your SP shows incorrect config-reg. Pls change it:

(config)# remote command switch config-reg 0x2102

[Soon Kwan Kwon]

First of all, I did

boot system flash disk0:s72033-ipservicesk9_wan-mz.122-18.SXF16.bin
boot system flash bootflash:

By the way,

Is is right there is no command "boot-start-marker", "boot-end-marker".

Anyway, I did 2 commands 

boot system flash disk0:s72033-ipservicesk9_wan-mz.122-18.SXF16.bin
boot system flash bootflash:

and "wr"

and "reload"

again rommon mode... 

now I'm trying to input "remote command switch config-reg 0x2102"

[Soon Kwan Kwon]

config-register is already 0x2102..

Anyway, I did command "remote command switch config-reg 0x2102"

but it was not applied..

I upload file!

[vivek srivastava]

Ok, but the problem is your SP config-reg is not correct (see the output of remote command switch show bootvar). Try once more with:

!

config-register 0x2102
wr

!

and then check the outputs of:

# show bootvar

# remote command switch show bootvar

[Soon Kwan Kwon]

I did!!

first. remote command switch show bootvar

second. config-register 0x2102

third. show bootvar

fourth. remote command switch show bootvar

I tried upper procedures...ㅠㅠ

I really don't know why it is not stored that I input?

I definitely input config-register 0x2102 and boot system disk0:s72033-ipservicesk9_wan-mz.122-18.SXF16.bin and wr .

and I turn it off and turn it on. but there is no command boot system disk0:~ in the show run although I input "write" command...

...Please teach me how to solve it!...

Please reply as soon as possible .. if possible!

I continuously keep an eye your reply!! 

[vivek srivastava]

Have tried reboot after "fourth.png" ??

[Soon Kwan Kwon]

Yes!..

As you referred, I tried reboot 

but it was still entering the ROMmon mode.

plz see the below photo.

Anything else I should do..?

[Soon Kwan Kwon]

Anything else I should do to solve??..