cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
8613
Views
5
Helpful
4
Replies

Cisco 2901 router Fan issue

Muhammad Talha
Level 1
Level 1

Router Fan speed is too high but environment shows normal can any one guide

 

SYSTEM POWER SUPPLY STATUS

==========================

 Internal Power Supply  Type: AC

 Internal Power Supply  12V Output Status: Normal

 

 External Redundant Power Supply is absent or powered off

 

SYSTEM FAN STATUS

=================

 Fan 1 OK, Low speed setting

 Fan 2 OK, Low speed setting

 Fan 3 OK, Low speed setting

 Fan 4 OK, Low speed setting

 

SYSTEM TEMPERATURE STATUS

=========================

 Intake Left temperature: 23 Celsius, Normal

 Intake Right temperature: 21 Celsius, Normal

 Exhaust Left temperature: 26 Celsius, Normal

 Exhaust Right temperature: 25 Celsius, Normal

 CPU temperature: 50 Celsius, Normal

 Power Supply Unit temperature: 43 Celsius, Normal

 

REAL TIME CLOCK BATTERY STATUS

==============================

 Battery OK (checked at power up)

 

SYSTEM POWER

===============

 Motherboard Components Power consumption = 74.8 WPower consumption =

 ISM 0.0 WPower consumption =

 NM/SM slot 1 3.8 W

 Total System Power consumption is: 78.6 W

 

 Environmental information last updated 00:00:18 ago

 

 

SYSTEM FAN STATUS

=================

 Fan 1 OK, fan level 1, Low speed setting, 11546 RPM, 40% PWM

 Fan 2 OK, fan level 1, Low speed setting, 5175 RPM, 40% PWM

 Fan 3 OK, fan level 1, Low speed setting, 5018 RPM, 40% PWM

 Fan 4 OK, fan level 1, Low speed setting, 5153 RPM, 40% PWM

 

SYSTEM TEMPERATURE STATUS

=========================

 Intake Left temperature: 23 Celsius, Normal

 Intake Right temperature: 21 Celsius, Normal

 Exhaust Left temperature: 26 Celsius, Normal

 Exhaust Right temperature: 25 Celsius, Normal

 CPU temperature: 49 Celsius, Normal

 Power Supply Unit temperature: 43 Celsius, Normal

 

REAL TIME CLOCK BATTERY STATUS

==============================

 Battery OK (checked at power up)

 

SYSTEM ALARMS SETTINGS

======================

 Fan tray removal or multi fan failure results in warning

 CPU Warning Over Temperature Alarm = 90C

 CPU Critical Over Temperature Alarm = 110C

 Intake Left Abnormal Temperature Alarm = 45C

 Intake Left Over Temperature Alarm = 57C

 Intake Right Abnormal Temperature Alarm = 45C

 Intake Right Over Temperature Alarm = 57C

 Exhaust Left Over Temperature Alarm = 75C

 Exhaust Right Over Temperature Alarm = 75C

 Power Supply Unit Over Temperature Alarm = 80C

 Power Supply Unit Over Critical Temperature Alarm = 95C

 

SYSTEM VOLTAGES

===============

 12V voltage = 12.434 V, Normal

 5V voltage = 5.146 V, Normal

 3.3V voltage = 3.322 V, Normal

 2.5V voltage = 2.502 V, Normal

 1.8V voltage = 1.822 V, Normal

 1.2V voltage = 1.199 V, Normal

 ASIC voltage = 1.044 V, Normal

 CPU Core voltage = 1.213 V, Normal

 

SYSTEM POWER

===============

 Motherboard Components Power consumption = 74.8 WPower consumption =

 ISM 0.0 WPower consumption =

 NM/SM slot 1 3.8 W

 Total System Power consumption is: 78.6 W

 

 Environmental information last updated 00:00:27 ago

 

ENVIRONMENTAL STRESS EVENTS

===========================

Critical Temperature: Maxium = 0

                      Total Duration = 0

 Exceed Fan Tray Removal Time: Maximum Time= 0

                               Total Time = 0

Total MCU access error count: 0

1 Accepted Solution

Accepted Solutions

The RPM for Fan 1 is high but it does not seem to be an issue from the looks of it -

Fan 1 OK, fan level 1, Low speed setting, 11546 RPM, 40% PWM

Are both the ISR running the same IOS ? Do you see any buffered warning messages if you do "show logg" ?

View solution in original post

4 Replies 4

R0g22
Cisco Employee
Cisco Employee
How do you know that it is too high ?

By comparing noise of 2 2901 router on the same rack..slightly high fan speed

The RPM for Fan 1 is high but it does not seem to be an issue from the looks of it -

Fan 1 OK, fan level 1, Low speed setting, 11546 RPM, 40% PWM

Are both the ISR running the same IOS ? Do you see any buffered warning messages if you do "show logg" ?

Hi Nipun,

I doesn't see any buffered msgs in logs, See in attached snap. Also PTCL router are running on 15.2 IOS while cybernet router is on 15.5.

 

 

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: