Hello. I have created a 5 different subnetworks using vlsm, they are all connected to the same router and each end device can talk to each other the problem is i am trying to implement NAT overload (PAT) so that the end devices using the private ip address scheme i have used can access the internet sharing a single IP address. However the data cannot find its way out of the private network onto the internet. When i try and ping the web server on my topology i get a 'destination host unreachable' error from my default gateway.
The following is a copy of my router log and a picture of my topology.
Router>enable
Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#enable secret class
Router(config)#enable password cisco
Router(config)#hostname router1
router1(config)#int fa8/0
router1(config-if)#ip address 192.168.0.1 255.255.255.224
router1(config-if)#ip nat inside
router1(config-if)#no shutdown
router1(config-if)#
%LINK-5-CHANGED: Interface FastEthernet8/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet8/0, changed state to up
router1(config-if)#int fa7/0
router1(config-if)#ip address 192.168.0.33 255.255.255.240
router1(config-if)#ip nat inside
router1(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet7/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet7/0, changed state to up
router1(config-if)#int se2/0
router1(config-if)#ip address 201.224.1.1 255.255.255.0
router1(config-if)#clock rate 56000
router1(config-if)#bandwidth 56
router1(config-if)#ip nat outside
router1(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial2/0, changed state to up
router1(config-if)#int fa1/0
router1(config-if)#ip address 192.168.0.49 255.255.255.240
router1(config-if)#ip nat inside
router1(config-if)#no shutdown
router1(config-if)#
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up
router1(config-if)#int fa6/0
router1(config-if)#ip address 192.168.0.65 255.255.255.248
router1(config-if)#ip nat inside
router1(config-if)#no shutdown
router1(config-if)#
%LINK-5-CHANGED: Interface FastEthernet6/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet6/0, changed state to up
router1(config-if)#int fa0/0
router1(config-if)#ip address 192.168.0.73 255.255.255.248
router1(config-if)#ip nat inside
router1(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
router1(config-if)#exit
router1(config)#ip route 201.224.2.0 255.255.255.0 se2/0
router1(config)#ip host router1 192.168.0.1 192.168.0.33 192.168.0.49
router1(config)#line con 0
router1(config-line)#login
% Login disabled on line 0, until 'password' is set
router1(config-line)#password cisco
router1(config-line)#line vty 0 5
router1(config-line)#login
% Login disabled on line 66, until 'password' is set
% Login disabled on line 67, until 'password' is set
% Login disabled on line 68, until 'password' is set
% Login disabled on line 69, until 'password' is set
% Login disabled on line 70, until 'password' is set
% Login disabled on line 71, until 'password' is set
router1(config-line)#password cisco
router1(config-line)#exit
router1(config)#access-list 100 remark standard
router1(config)#access-list 100 permit ip 192.168.0.0 0.0.0.255 any
router1(config)#ip nat inside source list 100 interface se2/0 overload
router1(config)#exit
router1#
[IMG]http://i57.tinypic.com/2jal2cy.jpg[/IMG]
http://tinypic.com/r/2jal2cy/8
